Americaloc ST4340 - User Manual

Activate your account and device AMERICALOC ST4340
Go to www.americaloc.com, select
United States and click the
Activate Now button.
Before using our products or installing a device, carefully read our legal terms which you can nd at
https://us.americaloc.com/legal_info.html
Fill in the required information. The IMEI
code can be found below the bar code
that is printed on the back of your device.
Your account will now be ready to use.
Go to www.americaloc.com and
log in with the username and
password established in the
previous step.
Purchase one of our service plans by
clicking on the Click to pay service button.
A window will open to provide you with
payment instructions.
Turn OFF and then ON the device after initial service payment. Your device already comes
with a SIM card installed. Please do not remove the SIM card.
1
3
2
4
5
Appearance and LED behavior
Welcome to AMERICALOC
IMPORTANT: Your complete satisfaction is our rst priority! If you have a problem or need assistance
please contact us at support@americaloc.com. Rest assured we will nd a solution for you. Our friendly,
knowledgeable customer service representatives are standing by to explain our services and to assist
you in getting the most from your GPS tracking service.
If you plan to use the unit outside of the U.S. please contact Americaloc support so we can congure
your unit or provide a dierent SIM card if needed.
If you do not wire the ignition cable please contact support so we can congure your unit to detect
ignition by motion.
LED Device Status
Blink Count
(Fast continuous ashing)
CEL
(blue)
GPS
(red)
Connected
Server Communication Error
LTE-M1 Communication Error
No network
SIM PIN Locked
Can not attach to Network
No SIM
Connected
GPS chip is searching GPS info
GPS Chipset Error or
GPS Antenna Error
1
2
3
4
5
6
7
1
2
4
The blue wire is used for ignition detection. It is strongly recommended to connect this wire to ignition
key at “RUN” position as shown above.
An alternative to connecting to the ignition switch is to nd a non-permanent power source (like the
power source for FM radio) that is only available when the vehicle is running. Ignition signal can be
congured to start transmitting information to the backend server when ignition is on and to enter
power saving mode when ignition is o.
GROUND
IGNITION
Ignition Positions
1 ) O
2 ) Accesories
3 ) Run (Use this one)
4 ) Start
1
2
3
4
Best place: Under front dashboard
Device Vin
-
8 V-32V
PINOUT
1. Vin, Red
2. GND, Black
3. IGN, Blue
ST4340
st
nd
rd
th
st
nd
rd
th
Installation Diagram ST4340
Note: Cables that are not used in this installation must be individually cut and covered with black/electrical
tape to avoid short circuit.
Recommendation: Professional installation is recommended. Stereo and car alarm installers
usually know how to install these devices.

Summary

Welcome and Support Information

Device Activation Guide

Account Creation and Activation

Follow steps to go to website, register, and activate device.

Service Plan Purchase

Select and pay for a tracking service plan via the website.

Device Power Cycle

Turn the device off and on again after service payment.

Device LED Indicators and Status

CEL (Blue) LED Status

Explains blue LED states for connection and errors.

GPS (Red) LED Status

Explains red LED states for GPS search and errors.

ST4340 Installation and Wiring

Recommended Installation Location

Best place for mounting is under the front dashboard.

ST4340 Wiring Pinout

Details connections for Vin, Ground, and Ignition wires.

Ignition Detection Wiring

Connect the blue wire to ignition key at 'RUN' for detection.

Frequently Asked Questions

Device Activation Time

Device is active after payment once turned off and on again.

Technology Working Principle

Device uses satellites for location and mobile networks for transmission.

SIM Card Requirement

Device ships with an installed SIM card that only works with it.

Location Visibility Issues

Check for poor mobile network or GPS signal.

Location Accuracy Factors

Accuracy depends on weather, buildings, trees, and water.

Weather and Temperature Effects

Rain, snow, and extreme temperatures can affect signal and device.

Tracking Service Payment

Renew service via prompt before expiry; no automatic debits.

Service Expiry Check

Check service expiry under 'Account options' then 'My services'.

Basic Location and History Instructions

How to Locate Your Device

View device location updates and configure settings via the website.

How to Watch Device History

Access historical data using date ranges or advanced search.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The AMERICALOC ST4340 is a GPS tracking device designed to provide real-time location data and various tracking features. It utilizes both GPS signals for location determination and mobile networks (LTE-M1) to transmit this data to Americaloc's servers.

Function Description:

The primary function of the AMERICALOC ST4340 is to track the location of a vehicle or asset. It continuously reads data from satellites to pinpoint its location and then uses a mobile network connection to send this information to a backend server. Users can access this location data through the Americaloc website or a dedicated mobile app ("Americaloc Viewer").

Key tracking features include:

• Real-time Location Updates: The device updates its location at predefined intervals, typically one minute while moving. This interval can be configured by the user.
• Historical Tracking: Users can view the past movements of the device by accessing the "History" tab, selecting specific date and time ranges, and viewing the path taken on a map.
• Ignition Detection: When the blue wire is connected to the vehicle's ignition, the device can detect when the ignition is turned on or off. This allows for specific notifications (e.g., "Ignition On") and can be configured to enter power-saving mode when the ignition is off. An alternative to connecting to the ignition switch is to find a non-permanent power source that is only available when the vehicle is running.
• Internal Memory: The device has internal memory to store locations in areas with poor mobile data coverage. This ensures that data is not lost and will be transmitted once the device reconnects to the network.
• Notifications: Users can configure email or text message notifications for various events, such as ignition on/off.

Important Technical Specifications:

• Power Input: The device operates on a voltage range of 8V-32V.
• Connectivity:
  • GPS: For location determination.
  • Mobile Network (LTE-M1): For data transmission to servers.
• SIM Card: The device comes with a pre-installed SIM card that is specific to the device and should not be removed.
• LED Indicators:
  • CEL (blue) LED: Indicates mobile network status.
    • 1 blink: Connected
    • 2 blinks: Server Communication Error
    • 3 blinks: LTE-M1 Communication Error
    • 4 blinks: No network
    • 5 blinks: SIM PIN Locked
    • 6 blinks: Cannot attach to Network
    • 7 blinks: No SIM
  • GPS (red) LED: Indicates GPS status.
    • 1 blink: Connected
    • 2 blinks: GPS chip is searching GPS info
    • 4 blinks: GPS Chipset Error or GPS Antenna Error
• Wiring:
  • Vin (Red): Power input.
  • GND (Black): Ground.
  • IGN (Blue): Ignition detection.
• Installation: Recommended to be installed under the front dashboard. Unused cables must be individually cut and covered with black/electrical tape to prevent short circuits.

Usage Features:

• Account Activation: Users must activate their account and device online at www.americaloc.com by filling in required information, including the IMEI code found on the back of the device.
• Service Plan Purchase: After activation, users need to purchase a service plan through the Americaloc website.
• User Interface: Access to device location and settings is provided through the Americaloc website and the "Americaloc Viewer" mobile app (available on Google Play Store and App Store).
• Device Settings: Users can configure various settings, including location update intervals (while in motion) and notification preferences (email/text messages).
• Troubleshooting: The manual provides guidance on common issues such as "device not visible on website" (due to poor mobile network or GPS signal) and "location slightly off" (due to environmental factors).
• Payment Management: Users are notified 10 days before service expiration and can renew their plan online. Automatic debits are not used.
• International Use: If planning to use the unit outside the U.S., users must contact Americaloc support for configuration or a different SIM card.
• Ignition Detection by Motion: If the ignition cable is not wired, Americaloc support can configure the unit to detect ignition by motion.

Maintenance Features:

• Self-Contained Unit: The device comes with a pre-installed SIM card, eliminating the need for user installation or removal of the SIM.
• Professional Installation Recommended: While not strictly a maintenance feature, professional installation helps ensure correct wiring and optimal performance, reducing the likelihood of issues that might require maintenance.
• Environmental Considerations: Users are advised to avoid placing the device in very hot or humid places, direct sunlight, or extreme temperatures, as these can damage the device, affect battery life, or cause signal degradation.
• Customer Support: Americaloc emphasizes customer satisfaction and provides support via support@americaloc.com and a phone number (8558303390) for assistance with problems or questions. Video tutorials are also available on their YouTube channel.

Americaloc ST4340 Specifications

General

Brand	Americaloc
Model	ST4340
Category	GPS
Language	English