EasyManua.ls Logo

American Standard 4A6V0024A1000B User Manual

American Standard 4A6V0024A1000B
72 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
SSAAFFEETTYY WWAARRNNIINNGG
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and
air-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered
equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the
literature and on the tags, stickers, and labels that are attached to the equipment.
August 2017
44AA--VV00--SSFF--11GG--EENN
Variable Speed AccuLink
Heat Pumps and Air Conditioners
4A6V0024A1000B
4A6V0036A1000B
4A6V0048A1000B
4A6V0060A1000B
4A7V0024A1000B
4A7V0036B1000B
4A7V0048A1000B
4A7V0060A1000B
4A7V0061A1000B
Scan to see help
videos on this
product
NNoottee:: “Graphics in this document are for representation only.
Actual model may differ in appearance.”
Service Facts

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the American Standard 4A6V0024A1000B and is the answer not in the manual?

American Standard 4A6V0024A1000B Specifications

General IconGeneral
BrandAmerican Standard
Model4A6V0024A1000B
CategoryAir Conditioner
LanguageEnglish

Summary

Service Facts

Outdoor Safety Section

Hazardous Voltage

Warning about severe personal injury or death from electrical shock.

Refrigerant Oil Hazards

Hazards associated with refrigerant oil and system handling.

Contains Refrigerant Warning

Warning about high-pressure refrigerant and potential injury.

Grounding Required

Importance of proper grounding for safety and equipment protection.

Service Valve Warning

Warning about abrupt release of system charge from service valves.

Brazing Required

Importance of brazing for refrigerant line joints.

High Leakage Current Warning

Warning about electrical shock hazards from leakage current.

Electrical Hazard Warnings

400 Volts Electrical Hazard

Warning about high voltage and safe servicing procedures.

Subcooling Charging Procedure

Charging: Weigh-In Method

Integrated Variable Speed Control (IVSC) Inputs/Outputs

IVSC LED Indicators and Sump Heat Control

Sequence of Operation

Control Operational Overview

Management of the unit by the IVSC.

Cooling Mode Operation

How the system operates in cooling mode.

Heat Pump Cooling Mode Operation

Cooling operation specific to heat pumps.

Sequence of Operation (Continued)

Heat Pump Heating Mode Operation

How the system operates in heating mode.

Defrost Mode Operation

System behavior during defrost cycles.

Defrost Control (Heat Pump Only)

Demand Defrost Operation

How demand defrost is initiated and managed.

Defrost Initiation Logic

Conditions and logic for initiating defrost.

Sensors: Compressor Dome Temperature

Sensors: Ambient Temperature Sensor (ODS)

Sensors: Coil and Suction Temperature

Sensors: Suction Line Pressure Transducer

Variable Speed Alert Codes

Control and Sensor Faults

Alerts for control failures and temperature sensor issues.

Defrost and High Pressure Faults

Alerts related to defrost and high-pressure monitoring.

Variable Speed Alert Codes (Continued)

Ground, Communication, and Shutdown Faults

Alerts for ground faults, communication issues, and external shutdowns.

PM, EEV, and Charge Faults

Alerts for PM, EEV, low charge, and unit bus communication issues.

Limp Mode and Drive Current Faults

Alerts for limp mode operation and drive current issues.

DC Voltage Failure Alerts

Alerts indicating DC voltage irregularities.

Power Module and Supply Voltage Alerts

Alerts for power module and supply voltage problems.

Gate Drive, Motor, and Rotation Faults

Alerts for gate drive, motor, and rotation issues.

Initialization, Startup, and Range Faults

Alerts for initialization, startup, and sensor range errors.

Protection Algorithm Faults

Alerts for protection algorithm and general faults.

Derating and Lubrication Faults

Alerts related to derating due to temperature and lubrication issues.

MOC Protection and Evacuation Faults

Alerts for MOC protection and evacuation mode.

Drive Diagnostics and Configuration Faults

Alerts for drive diagnostics and configuration errors.

Voltage and Bus Communication Faults

Alerts for voltage irregularities and bus communication issues.

Superheat and Sensor Faults

Alerts related to superheat and suction pressure sensor errors.

Load Shedding

Communication Loss Troubleshooting

Breaker Trip Procedure

Breaker Trip Troubleshooting Flowchart

Step-by-step guide for troubleshooting breaker trips.

Start Compressor Troubleshooting

Compressor Startup Flowchart

Flowchart for diagnosing compressor startup issues.

Compressor Verification: Parameters

Run Drive Diagnostic Test

Compressor Verification: Short

Compressor Verification: Open

Inverter Temperature Troubleshooting

EEV Troubleshooting Flowchart

Communicating Display Assembly (CDA)

Technician Monitor Menu

Technician Alert Menu

Technician Alert History Menu

Technician Configuration Menu

Technician Control Menu

Technician Control Menu (Continued)

TECH CONTROL - Charge/Check Charge Modes

Warranty Claim Process

Related product manuals