American Standard Afwall Wall 1.6 GPF Flush Valve Wall-Mounted Toilets 2254 User Manual

SAVE FOR FUTURE USE
1
730484-100
Saniwares
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2000
!
2
Refer to instructions supplied with wall carrier for proper installation of 4-bolt support
system wall cavity requirements and rough-in information for waste outlet piping.
Closet Carrier Support
Putty Knife
Sealant
Tape Measure
Regular Screwdriver
Adjustable Wrench
Carpenters Level
Flush Valve
RECOMMENDED TOOLS AND MATERIALS
Pictures may not exactly define contour of china
Model 2254, 2256, 2257, 2258
AFWALL 1.6 GPF FLUSH VALVE
WALL-MOUNTED TOILETS
INSTALLATION INSTRUCTIONS
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR
HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
FIXTURE MOUNTING
Fixture studs should project
1-7/8" (48mm) from face of
finished wall.
Front View
Side View
FINISHED
WALL
1-7/8"
(48mm)
(4) STUDS
Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged
When installed,
top of seat is
17" to 19"
(432mm to 483mm)
from the finished
floor.
FINISHED WALL
470mm
(18-1/2)
C/L OF SEAT POST
HOLES 140 mm
(5-1/2) CENTER
635mm
(25)
73mm
(2-7/8)
184mm
(7-1/4)
133mm
(5-1/4)
191mm
(7-1/2)
292mm
(11-1/2)
(4) 22mm
(7/8)
HOLES
375mm
(14-3/4)
C/L OF
OUTLET
121mm
(4-3/4)
FINISHED
FLOOR
32mm
(1-1/4)
381mm
(15)
or
432mm
(17)
381mm
(15)
or
432mm
(17)
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
330mm
(13)
19mm
(3/4)
133mm
(5-1/4)
98mm
(3-7/8)
70mm
(2-3/4)
1-1/2 SPUD
C/L
229mm
(9)
FINISHED WALL
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm(5-1/2) CENTERS
635mm
(25)
191mm
(7-1/2)
298mm
(11-3/4)
(4) 22mm (7/8)
DIA. HOLES
375mm
(14-3/4)
C/L OF
OUTLET
FINISHED
FLOOR
32mm
(1-1/4)
330mm
(13)
(3/4)
19mm
133mm
(5-1/4)
98mm
(3-7/8)
C/L
229mm
(9)
38mm (1-1/2) DIA. HOLE IN WALL
95mm
(3-3/4)
FOR WALLS UP TO 1" IN THICKNESS FOR EACH INCH
ADDITIONAL THICKNESS OF WALL ADD 25mm (1) TO
MEASUREMENT SHOWN
89mm
(3-1/2)
1" C.W.T. OR N.P.T. SUPPLY
AS REQ'D NOT FURNISHED
121mm
(4-3/4)
VACUUM BREAKER
76mm(3) DIA. HOLE IN WALL
FOR 1-1/2 SPUD
254mm
(10)
41mm
(1-5/8)
38mm
(1-1/2)
70mm
(2-3/4)
or
184mm
(7-1/4)
133mm
(5-1/4)
or

American Standard Afwall Wall 1.6 GPF Flush Valve Wall-Mounted Toilets 2254 Specifications

General

Brand	American Standard
Model	2254
Flush Rate	1.6 GPF
Mounting	Wall-Mounted
Material	Vitreous China
Flush Type	Flush Valve
Flush Volume	1.6 GPF
Installation Type	Wall-Mounted
Category	Plumbing Product
Type	Wall-Mounted Toilet
Fixture Type	Toilet

Summary

Fixture Mounting

Fixture Stud Projection

Fixture studs should project 1-7/8" (48mm) from the face of the finished wall.

Installation Steps

Back-up Nut Adjustment

Adjust back-up nuts on bottom bolts and top left bolt. Ensure front faces of lower nuts are flush with wall.

Waste Horn Projection

Adjust waste horn to project 5/16" (7mm) from the finished wall.

Top Back-up Nut Alignment

Align top left back-up nut vertically with lower left nut for a minimum 1/16" gap.

Bearing Nut and Washer Setting

Set bearing nuts/washers to load fixture, allowing 1/16" clearance between fixture and wall.

Helper Assisted Installation

Helper installs bowl with cap nuts and fiber washers. Avoid tightening top right nut until others are secure.

Sealant Application

Apply sealant to the gap between the bowl and finished wall, then remove excess.

American-Standard One-Year Limited Warranty

Warranty Coverage

Covers defects in materials or workmanship within one year of installation. Excludes local code compliance.

Warranty Exclusions

Void if product is moved, subjected to abuse, faulty maintenance, or not installed per instructions.

Limitations on Damages

Excludes labor, installation costs, and incidental/consequential damages.

Service and Claims

Claims should be made through the contractor or dealer, or submitted to American Standard.