American Standard OVATION 2968BWT60 User Manual

755578-100 Rev. 4 02/20
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2020
INSTALLATION INSTRUCTIONS
OVATION
®
BATH AND SHOWER
WALL SETS
MODELS: 2968BWT60, 2968SWT60
SAVE FOR FUTURE USE
NOTE: Remove protective plastic coating material from surface of panel before installation.
Take extra care in handling the front surfaces of the walls. Use only non-abrasive cloths to avoid scratching.
Thank you for selecting American Standard - the benchmark of fine quality for over 140 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.)
REQUIRED TOOLS AND MATERIALS
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Unpack your new walls and inspect them carefully for damage. Verify that the walls are the correct size for your installation.
Refer to American Standard roughing-in information for specific dimensions for each model.
Tape Measure
Caulking Gun
Hole Saw or Jig Saw
with fine tooth blade
Pencil
Drill
Square
Level
TOOLS:
Waterproof Adhesive
Tub & Tile Sealant
Mineral Spirits
Safety Glasses
Masking Tape
MATERIALS:
Visit www.americanstandard.com for coordinating products.
PREPARATION: Must be installed over SHEETROCK/GREENBOARD.
A) WALL SURFACE PREPARATION
NOTE: For best adhesion, we suggest priming walls prior
to installation.
Ensure wall surface is dry, smooth, and free of dust, soap
scum, mold or other contaminants. Wipe wall surfaces with
a damp cloth and allow to dry.
Wall surface must be dry before panels can be applied.
Ensure that alcove is plumb and square. See Illustration 1.
B) ROUGH PLUMBING & FITTINGS MUST BE INSTALLED
BEFORE WALLS
Turn off hot & cold water supplies.
Remove faucet handles, escutcheons, filler spouts and any
other fixtures & fittings (e.g. towel bars, soap dishes, etc.).
C) IF YOU PLAN TO INSTALL A SHOWER DOOR
Follow manufacturer’s instructions and prepare stud wall
accordingly.
Illustration 1
EACH ALCOVE STUD MUST
BE PLUMB AND SQUARE.

American Standard OVATION 2968BWT60 Specifications

General

Brand	American Standard
Model	OVATION 2968BWT60
Category	Plumbing Product
Type	Toilet
Material	Vitreous China
Length	28.5 inches
Installation Type	Floor Mounted
Shape	Elongated
Drain Location	Floor
Product Type	Toilet
Rough-In Size	12 inches
Bowl Height	16.5 inches
Bowl Shape	Elongated
Color	White
Warranty	Limited Lifetime
Flush Type	Gravity
Water Consumption	1.6 GPF
Flush Valve Size	3 inch

Summary

Preparation

Wall Surface Preparation

Prepare wall surface by ensuring it is dry, smooth, and free of contaminants for adhesion.

Rough Plumbing and Fittings Must Be Installed Before Walls

Ensure all plumbing and fixtures are installed before attaching wall panels.

If You Plan to Install a Shower Door

Follow manufacturer's instructions for shower door installation preparation.

Dry Fitting the Panels on the Wall

Dry fitting rear panel

Center and position the rear panel, marking reference lines for alignment.

Dry fitting side panels

Position side panels, ensuring correct gaps and marking reference lines.

Mark plumbing locations

Mark and drill holes for plumbing fixtures on side panels.

Installing in a 48-inch Shower Alcove

Procedure for trimming the rear panel to fit a 48-inch shower alcove.

Installing Back and Side Walls

Apply adhesive to walls

Apply adhesive in a zig-zag pattern on walls within marked lines for panel attachment.

Position and press rear panel

Place rear panel, ensuring 1/8" gap, and press firmly for adhesive contact.

Install side panels

Install side panels similarly, wiping excess adhesive with mineral spirits.

Installing the Corner Panels

Check corner panel fit

Place corner panel, align right-side up, and ensure it overlaps other panels.

Apply adhesive and position corner panel

Apply adhesive to the back of the corner panel and press firmly into place.

Wipe down panel

Wipe panel with a damp rag while applying pressure for complete contact.

Applying Sealant and Installing Hardware

Allow adhesive to dry

Allow wall panel adhesive to dry for 24 hours before applying sealant.

Apply sealant

Apply sealant around all corners, edges, and fixtures for waterproofing.

Install shower handle and shower head

Install shower handle and head per manufacturer's instructions.

Post Installation Clean-Up

Remove construction debris

Remove all construction debris, avoiding wire brushes or metal implements.

General cleaning

Clean with warm water and mild dishwashing detergent.

Remove excess adhesive

Use painter's naphtha for excess adhesives or wet oil-base paint.

Aftercare and Cleaning Precautions

Avoid harsh chemicals

Use only mild liquid household detergent; avoid specific listed cleaners.

Do not use abrasive tools

Avoid wire brushes, knives, or sharp objects for stain removal.

Avoid abrasive cleaners

Do not use abrasive cleaners or powders, as they will dull the surface.

Do not use solvents

Avoid contact with nail polish remover, acetone, or other listed solvents.