Why does my Amiko Set-top boxes say no signal?
A 'No signal' message on your Amiko Set-top box might appear if the signal level is weak, the LNB is out of order, the cable from the LNB is incorrectly connected (short circuit or open circuit), or the dish position is aligned incorrectly.
Why is there no picture on my Amiko Set-top boxes screen?
If there is no picture on the screen when using your Amiko Set-top boxes, the receiver might be in Standby mode. Also, check if the RCA jack or cable is not connected firmly to the video output port of the television, ensure the correct channel or video output is selected on the television, or verify that the brightness level of your TV set is correctly defined.
What to do if Amiko Set-top boxes remote is not working?
If your Amiko Set-top boxes receiver isn't responding to the remote control unit (RCU), the RCU batteries might be dead or inserted incorrectly. Also, make sure the RCU is pointing in the right direction.
How to fix no sound on Amiko Set-top boxes?
If there is no sound from your Amiko Set-top boxes, check if the cable is connected correctly, ensure the volume level is not too low, and verify that the muting function is not active.
Why is the picture quality poor on my Amiko Set-top boxes?
If you're experiencing poor picture quality with your Amiko Set-top boxes, it could be due to a low signal strength.
What to do if Amiko Set-top boxes shows 'No TV program'?
If your Amiko Set-top boxes receiver is on but there's no picture or sound (with a 'NO TV program' message), it could be because the channel is not available or the channel is scrambled.
Why haven't settings changed on my Amiko Set-top boxes?
Settings you made in the Amiko Set-top boxes menu might not change if the receiver lost power before entering standby mode or some settings saved by the user were partly or fully deleted.
Why is there no display on the Amiko Set-top boxes LED Display Panel?
If there is no display on the LED Display Panel of your Amiko Set-top boxes, the power cord may not be plugged in correctly.
Powers the receiver on or puts it into standby mode.
Accesses the Electronic Program Guide for channel schedules.
Configures satellite reception, LNB settings, and scanning.
Simplifies channel scanning by provider selection.
Automatically detects and scans services from dishes.
Configures terrestrial reception, scan modes, and frequencies.
Sets up cable TV reception, including frequencies.
Adjusts video resolution, aspect ratio, and audio output.
Updates receiver software using a USB drive.
Updates software from an internet server.
Resets receiver parameters to factory defaults, erasing user data.
Shows information about inserted conditional access cards.
Manages conditional access information for CAM modules.
Plays back recorded video files, allowing file management.
Plays video files from USB storage.
Plays audio files from USB storage.
Allows pausing and rewinding live TV broadcasts.
Enables recording of TV programs to USB storage.
Powers the receiver on or puts it into standby mode.
Accesses the Electronic Program Guide for channel schedules.
Configures satellite reception, LNB settings, and scanning.
Simplifies channel scanning by provider selection.
Automatically detects and scans services from dishes.
Configures terrestrial reception, scan modes, and frequencies.
Sets up cable TV reception, including frequencies.
Adjusts video resolution, aspect ratio, and audio output.
Updates receiver software using a USB drive.
Updates software from an internet server.
Resets receiver parameters to factory defaults, erasing user data.
Shows information about inserted conditional access cards.
Manages conditional access information for CAM modules.
Plays back recorded video files, allowing file management.
Plays video files from USB storage.
Plays audio files from USB storage.
Allows pausing and rewinding live TV broadcasts.
Enables recording of TV programs to USB storage.
General| Video Resolution | 1080p |
|---|---|
| Connectivity | HDMI, USB, Ethernet |
| Tuner Type | DVB-S2 |
| Operating System | Proprietary |
| Flash Memory | 8 MB |
| S/PDIF | Yes |
| Card Reader | Yes |
| Audio Formats | MP3, AAC |
| CI Slot | No |
| Weight | 0.5 kg |
| Audio Output | HDMI, S/PDIF |
| Video Decoding | H.264 |
| Video Formats | H.264, MPEG-2 |
| Ethernet | 10/100 Mbps |
| Power Consumption | 10W |
| RAM | 512 MB DDR3 |
| Dimensions | 144 x 110 x 40 mm |
To Next Page
