EasyManua.ls Logo

Amkus ion 2.0 - User Manual

Amkus ion 2.0
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
©Copyright AMKUS Rescue Systems, Inc. 2016-2019 LAI-001 January 29, 2019 Rev03
DANGER
Understand manual before use. Operating AMKUS Rescue Systems without understanding
the manual, receiving proper training, and using appropriate personal protective
equipment is a misuse of AMKUS equipment. This manual does not fully address safety.
Additional safety information is published in AMKUS Safety Manual LAA-001 and Safety
Data Sheet LAA-040. Instructions for safe operation of DEWALT lithium ion batteries
and chargers are included with DEWALT packaging. Obtain safety information at
amkus.com/resources/documentation
Manual: ION 2.0 Battery Powered
Electro-hydraulic Rescue Tools
AMKUS RESCUE SYSTEMS
AMKUS.com
4201 Montdale Drive, Valparaiso, IN 46383-4098 USA
800-592-6587 • 219-548-5000
CUTTER
Model: iC550
SPREADER
Model: iS240, iS240-L, iS280, iS280-L
COMBI TOOL
Model: iCT516
RAM
Model: iTR230
BATTERY
DEWALT® DCB606 60VDC Lithium Ion Part#: IBATTFV-6
CHARGER
DEWALT® DCB118 1 Hour Charger, 120 VAC Part#: ICHRG120
HYDRAULIC SYSTEM
Self-contained, 10,150 PSI (700 bar) high-speed single stage pump
HYDRAULIC FLUID
AMKUS MV0 (Mineral Oil base) part#: KF0007
Safety Data Sheet (SDS) for AMKUS MV0 Hydraulic Fluid is available at AMKUS.com and
CHEMTREC.com
2.0
60 VOLT
Maximum
Power
Certifi ed Compliant to
NFPA 1936, 2015 Edition

Table of Contents

Questions and Answers

  • J
    Jennifer VasquezAug 12, 2025
    Why won't my Amkus Tools motor start?
    • A
      ayorkAug 12, 2025
      If the Amkus Tools motor doesn't start, there might be a few reasons: * The battery could be defective, in which case you should replace it. * The tool might not be turned on; press the power button for 3 seconds. * The battery might not be charged, so ensure it is properly charged.
  • K
    Keith AcostaAug 19, 2025
    What to do if my Amkus Tools motor does not stop?
    • T
      tranjamesAug 19, 2025
      If the Amkus Tools motor does not stop, it could be due to a shorted battery, in which case the battery should be replaced. Alternatively, the control valve actuator might be stuck. Try blowing out the control valve with air. If the issue persists, consult an Authorized AMKUS Service Technician.
  • J
    justin05Aug 27, 2025
    How to fix an overheated electronic motor in Amkus Tools?
    • M
      michaelparkerAug 27, 2025
      If the electronic motor in your Amkus Tools overheats, it could be due to an overheated battery. Allow the battery to cool down. Alternatively, the cooling vents might be obstructed, so clean the cooling vents.
  • D
    Donna HillSep 2, 2025
    What to do if the stroke does not begin on my Amkus Tools?
    • J
      Jennifer CollinsSep 3, 2025
      If the stroke does not begin in your Amkus Tools, the control valve actuator might be damaged. Replace the control valve to resolve this issue.

Amkus ion 2.0 Specifications

General IconGeneral
BrandAmkus
Modelion 2.0
CategoryPower Tool
LanguageEnglish

Related product manuals