Andersen 618803 User Manual

1
Handle Installation Guide
Please Do Not Return Product to Store!
PLEASE call the storm door Solution Center at 1-800-933-3626
Note: Instructional images show
Traditional handleset, follow the same
procedure for Modern handleset.
Your storm door lock can be changed (re-
keyed) to match your main door’s handle
set if it’s a Kwikset® (included) or a Schlage®
(additional purchase required). Many
home improvement stores or locksmiths
can make duplicate keys.
“Kwikset” is a registered trademark of
Newfry LLC. “Schlage” is a registered
trademark of Schlage Lock Company.
Andersen Storm Door Division is a wholly owned subsidiary of Andersen Corporation. Andersen
Storm Door Division manufactures and supports the limited warranties for Andersen® and
EMCO® storm doors. “Andersen” and “EMCO” and all other marks where denoted are trade-
marks of Andersen Corporation. ©2018 Andersen Corporation. All rights reserved.
Andersen SDD, PO Box 853
Des Moines, IA 50306-0853
09-2018 r3 18011 Print in Color
PARTS OVERVIEW
Figure 1
P/N 618803
with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase.
Read this entire guide before you begin your installation. If your abilities do not
match the requirements of this installation, contact an experienced contractor.
Entry door hardware and handle
may become hot when exposed to
sunlight.
WARNING
Ed
Improper use of hand or power tools could result in injury
and/or product damage. Follow equipment manufacturer’s
instructions for safe operation. Always wear safety glasses.
WARNING
RECOMMENDED TOOLS
Safety Glasses
Screwdriver
=
=
X
VIEW
VIEW
i
VIEW
VIEW
EXTERIOR VIEW
EXTERIOR VIEW
VISTA EXTERIOR
VISTA EXTERIOR
VUE DE L’EXTÉRIEUR
VUE DE L’EXTÉRIEUR
INTERIOR VIEW
INTERIOR VIEW
VISTA INTERIOR
VISTA INTERIOR
VUE DE
VUE DE
L’INTÉRIEUR
L’INTÉRIEUR
A
B
C
D
E
F
G
H
I
A
B
C
D
E
F
G
H
I
G
SAFETY FIRST: PLEASE READ AND FOLLOW ALL CAUTIONS AND WARNINGS IN THIS GUIDE.
Outside Trim Plate
Inside Trim Plate
Handle without Spindle
Handle with Spindle
Lock Case Trim Plate
Dead Bolt Key Cylinder
#8 x 1 1/2" Screw (2)
#10 x 1 1/2 Screw
#10 x 1 5/8 Screw
Modern
Traditional

Andersen 618803 Specifications

General

Brand	Andersen
Model	618803
Category	Door Opening System
Language	English

Summary

Parts Overview

Recommended Tools

Safety Warnings

Handle Temperature Warning

Entry door hardware and handle may become hot when exposed to sunlight.

Tool Usage Warning

Improper use of hand or power tools could result in injury and/or product damage. Always wear safety glasses.

Install Handle Set (Right Hand)

Inspect Handle Holes

Look into handle holes on door to ensure lock case is oriented properly. Notch in square spindle hole should face downwards.

Insert Handles into Trim Plates

Insert handle without spindle into outside trim plate. Rotate handle 180° to secure. Repeat for other handle.

Rotate and Install Handles

Rotate handle levers into a vertical position. Install both handle assemblies onto the door. Spindle passes through square hole.

Install Lock Case and Cylinder

Install lock case trim plate onto lock case. Insert dead bolt key cylinder into lock case.

Install Handle Set (Left Hand)

Inspect Handle Holes

Look into handle holes on door to ensure lock case is oriented properly. Notch in square spindle hole should face downwards.

Insert Handles into Trim Plates

Insert handle with spindle into outside trim plate. Rotate handle 180° to secure. Repeat for other handle.

Rotate and Install Handles

Rotate handle levers into a vertical position. Install both handle assemblies onto the door. Spindle passes through square hole.

Install Lock Case and Cylinder

Install lock case trim plate onto lock case. Insert dead bolt key cylinder into lock case.