−
1
−
INSTRUCTION MANUAL
Spray Gun
Be sure to observe warning s and cautions in this instruction manual.
If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.
Be sure to observe following marked items which are especially important
.
Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage.
Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the
minimum necessary conditions. Follow national and local regulations regarding fire prevention, electricity
and safety as well as your own company regulations.
Symbol Marking on the Spray Gun:
II 2 G Ex h X
complies to machinery directive
2006/42/EC and ATEX directive
2014/32/EU,for EU market and
machinery regulations 2008
No.1597 ATEX directive 2016
No.1107 for UK market.
II
2
G
Ex h
IIB
T6
Gb
X
T
Amb
+5°C +40°C
Complies
with
European
Directive
Specific
Marking for
Explosion
Protective
Group II
(Surface)
Category
(Zone 1&2)
Type of
Atmosphere
(GAS)
Ignition
Protection
(not applied)
Explosion
Group
(Ethylene)
Temperature
Class
(≤ 85°C)
Explosion
Protection
level
(EPL)
conditions: Any
static Electricity
should be
discharged and
needs to be
diverted to the
ground via a
conductive air hose
Ambient
Temperature
Important specifications
Max. Pressure 0.70MPa / 7.0bar / 100psi
Noise level 79dB(A)
Spray condition Recommended
Measuring point 1m backwards from spray gun, 1.6m height
Max. temperature Atmosphere: 5°C ~40°C (41°F~104°F) Air and Fluid: 5°C ~43°C (41°F~109°F)
Important
Never connect pressure feeding paint except pressure feed type spray gun.
Main specifications
Model
Type of
feed
Nozzle orifice
Φ mm (in)
Air cap assy
Mark
Recommended condition
Air
consumption
L/min (cfm)
Pattern width
mm (in)
Spray
distance
mm (in)
Paint
Viscosity
s/Ford#4
Air & fluid
Mass
g (lbs.)
Atomizing air pressure
※
1
MPa (bar / PSI)
Fluid output
mL/min
Gravity
200 (7.9)
16
Air
G1/4
(NPS1/4)
Fluid
G1/4
(NPS1/4)
290
(0.64)
B2 0.24(2.5/36)
230 (8.1)
KP6 0.20 (2.0/29)
200 (7.1)
16
B8 0.20 (2.0/29)
230 (8.1)
※
※
※
※
-14B8
1.4 (0.055) B8 0.20 (2.0/29)
230 (8.1)
200 (7.9)
Nozzle needle assy combination
Fluid nozzle Fluid needle
Model Orifice Φ mm (in) Mark Mark
KIWAMI-1-13B4 Φ 1.3 (0.051) / K1 / 13B4
13 WIDER1
KIWAMI-1-14B2 Φ 1.4 (0.055) / K1 / 14B2
KIWAMI-1-16B2 Φ 1.6 (0.062) / K1 / 16B2 13H WIDER1
KIWAMI-1-13KP6 Φ 1.3 (0.051) / K1 / 13KP6
13 WIDER1
KIWAMI-1-14KP6 Φ 1.4 (0.055) / K1 / 14KP6
KIWAMI-1-13B8 Φ 1.3 (0.051) / K1 / 13B8
KIWAMI-1-14B8 Φ 1.4 (0.055) / K1 / 14B8
KIWAMI-1-13B10 Φ 1.3 (0.051) / K1 / 13B10
KIWAMI-1-16B12 Φ 1.6 (0.062) / K1 / 16B12
KIWAMI-1-18B14 Φ 1.8 (0.069) / K1 / 18B14
18 WIDER1
KIWAMI-1-14B8S Φ 1.4 (0.055) / K1 / 14B8
13 WIDER1
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS.
Equipment in this manual is exclusively for
painting purposes.
Do not use for other purposes.
The operator shall be fully conversant with
the requirements stated in this instruction
manual including important warnings,
cautions and operation and correct handling.
Read and understand the instruction
manual, before use and retain for reference.
IMPORTANT WARNING: Our spray guns, airbrushes, and other products are made to conform by our local group companies with local
that may differ from place to place. Improper trade of products outside of designated domestic territories (unauthorized reselling) can result in legal violations,
local fines, and penalties. ANEST IWATA CORPORATION assumes no liability for products acquired through unauthorized reselling and in such cases and due
to quality control protocols, unauthorized reselling renders the warranty null and void.
※
1. Atomizing air pressure means air pressure at gun inlet when trigger is pulled and air flows
．
※
2. Opening of fluid adjust knob is 3 turns from full close.
To Next Page
Need help?
General
