Annovi Reverberi PROLINER 8.150 User Manual (English)

Questions and Answers:

R
randy06Aug 16, 2025
Why does the pump pressure of my Annovi Reverberi Pressure Washer drop suddenly during use?
- M
  Megan EstradaAug 16, 2025
  If the pump pressure of your Annovi Reverberi Pressure Washer drops suddenly during use, it could be due to several reasons. One potential cause is that the water is being drawn from an external tank; try connecting the appliance to the mains water supply. Another reason could be that the inlet water is too hot; reduce the water temperature. Additionally, the nozzle or the inlet filter might be clogged; clean the nozzle or the filter to resolve this issue.
B
Barbara RogersAug 19, 2025
Why does my Annovi Reverberi Pressure Washer motor buzz but not start?
- O
  Olivia MarshAug 19, 2025
  If your Annovi Reverberi Pressure Washer motor buzzes but fails to start, it could be due to several reasons. First, the power supply voltage might be too low, so check that the voltage of the mains power supply line matches what's indicated on the appliance's plate. Second, a voltage drop could be occurring because of the extension cable being used; check the characteristics of the extension cable. Third, if the appliance hasn't been used for a long time or there are problems with the TSS device, it is recommended to contact your nearest Authorised Service Centre.
J
Joe TurnerAug 23, 2025
What to do if my Annovi Reverberi Pressure Washer motor fails to start?
- A
  aelliottAug 23, 2025
  If your Annovi Reverberi Pressure Washer motor fails to start, there are a few things you can check. First, ensure that the plug is firmly in the socket and that the mains voltage supply is present. Second, if there are problems with the TSS device or the appliance has not been used for a long period of time, it is recommended to contact your nearest Authorised Service Centre. However, if your model has this feature, you can try using the tool to unjam the motor through the hole at the rear of the appliance.
P
Paul BakerAug 27, 2025
Why is my Annovi Reverberi Pressure Washer not sucking in detergent?
- R
  Robert CampbellAug 27, 2025
  If no detergent is being sucked into your Annovi Reverberi Pressure Washer, consider these potential causes: The adjustable nozzle may be on a high-pressure setting; set it to the " " setting. The detergent may be too dense; dilute it with water. A high-pressure hose extension might be in use; fit the original hose. There may be deposits or a restriction in the detergent circuit; flush with clean water and eliminate any restrictions. If the problem persists, it is recommended to contact an Authorised Service Centre.
D
Dustin BrownAug 31, 2025
Why does water escape from the thermostat valve of my Annovi Reverberi Pressure Washer?
- S
  Sandra RichardsonAug 31, 2025
  If water escapes from the thermostat valve of your Annovi Reverberi Pressure Washer, it's likely because the water temperature inside the pump head has exceeded the maximum rated value stated on the nameplate. To prevent this, when the appliance is in operation, avoid stopping the water jet for more than 5 minutes at a time.
T
toniharrisSep 3, 2025
Why is my Annovi Reverberi Pressure Washer so noisy?
- R
  Randy MarquezSep 3, 2025
  If your Annovi Reverberi Pressure Washer is excessively noisy, it might be because the water is too hot. Reduce the temperature according to the technical data.
J
Jessica DanielsSep 7, 2025
Why is there no water coming out of my Annovi Reverberi Pressure Washer (TSS version) when I depress the gun trigger?
- R
  Raymond MurphySep 7, 2025
  If there's no water delivery when the gun trigger is depressed on your Annovi Reverberi Pressure Washer (TSS versions only), and the supply hose is connected, the nozzle might be clogged. Try cleaning the nozzle to resolve the issue.