45
7. ADVANCED SET-UP continued …
menu 7.b-c/k) Select Source:
Allows you to select the source that will play when either Timer1 or Timer2 turns a Zone / Path On. All sources
are available (even your favorite FM/AM station). Be sure that your selected source and power amplifier are
turned on, or will be at the Timer turn-on time – if your components are equipped with trigger inputs, you can
set an AVM 2 Trigger to turn them on (see section 7.4.8).
The sources available for Timer turn-on are: TV, SAT, VCR, AUX, DISC1, DIRECT, DISC2, TAPE, and Last Stn
(the tuner setting when AVM 2 was last turned off). For example, to select a Source for the ZONE2 Timer:
• Enter the Setup Menu (section 7.1). Go to ‘7. TIME/TIMERS’ and press SELECT (‘Select’).
• Press the 6 (‘Down’) key until you reach “c. SET ZONE2 TIMERS”.
• Press SELECT (‘Select’). The ‘7c. SET ZONE2 TIMERS’ Submenu will appear.
• Press the 6 (‘Down’) key until you reach “k. SELECT SOURCE”.
• Use the 34 keys (MASTER CONTROL KNOB) to change to desired Source Component.
• Press the EXIT (‘ B a c k ’) key to leave this submenu and return to TIME / TIMERS menu.
If you selected ‘Last Stn’ as your Timer turn-on source, you can leave it set to the last station you were
listening to, or choose one of your preset stations. For example, to have the Zone / Path Timer turn-on to a
Preset Station, do the following from the ‘k. SELECT SOURCE’ menu line (above):
• Use the 34 keys (MASTER CONTROL KNOB) to change to ‘Last Stn’.
• Press SELECT (‘Select’) to highlight ‘Last Stn’.
• Use the 5 6 keys (MASTER CONTROL KNOB) to change to desired FM/AM Preset. T h e s e
will scroll from ‘AM 1-1’ to ‘AM 1-6’ to ‘FM1-1’ through to ‘FM3-6’ and back to ‘Last Stn’.
• Press the SELECT or EXIT (‘ B a c k ’) key to go back to the menu line.
( m e n u 7.b-c/l) Auto-On Vo l u m e :
Sets the Volume that will play when Timer1 or Timer2 turns the Power- O n .
(menu 7.b-c/m) Volume Options:
Choose whether you want the Volume to come on immediately at the ‘AUTO-ON’ Volume setting or ‘RAMP-
UP’ to that setting. With Ramp-Up the volume starts at the minimum volume for that Zone / Path and slowly
increases until the ‘Auto-On Volume’ setting is reached.
TIME / TIMERS Example: Change ZONE2, TIMER2 to come on Weekdays at 7:35 AM.
• Enter the Setup Menu (section 7.1). Go to ‘7. TIME/TIMERS’ and press SELECT (‘Select’).
• Press the 6 (‘Down’) key until you reach “c. SET ZONE2 TIMERS”.
• Press SELECT (‘Select’). The ‘7c. SET ZONE2 TIMERS’ Submenu will appear.
• Press the 6 (‘Down’) key to reach “f. TIMER2 OPTIONS: Off”.
• Use the 34 keys (MASTER CONTROL KNOB) to change to ‘Week’.
• Press the 6 (‘Down’) key until you reach “g. T2 WEEKDAY ON: 8:00 AM”.
• Press SELECT (‘Select’). The hour is now in red, press the 56 keys (MASTER CONTROL KNOB)
to set the hour to ‘7’ AM. (Continuing through ‘12’ will advance the AM/PM settings.)
• Press the 4 (‘Down’) key. ‘00’ minutes will be highlighted.
• Use the 56 keys (MASTER CONTROL KNOB) to set the minutes to ‘35’.
• Press the EXIT (‘ B a c k ’) key to leave this submenu and return to TIME / TIMERS menu.
To Next Page
Loading...