10
In the recording status, press the “Record/OK" button to suspend the
video, and then press the “Menu" key to enter the menu mode.
By entering the menu mode to select different function parameters
and turn on and off various functions.
Features:
G-sensor: Acceleration sensor. When the G-sensor detects the
emergency braking of the vehicle during driving, the video of this
period of time will be saved separately and will not be automatically
deleted.
WDR: Wide Dynamic Range. It can clearly display the extremely
bright part and extremely dark part at the same time.
Loop Recording: Automatically overwrite the unlocked video when
the TF card is full, to ensure the normal recording.
Parking Monitoring: Under parking mode, the dash cam is in the
power-off condition. The dash cam will automatically turn on and
record when detect a vibration.
Motion Detection: In the standby mode, the dash cam is in the
power-on condition. The dash cam will automatically start record-
ing when detect a motion in front of the car.
Resolution: This setting allows you to set one of three available video
recording resolutions, 1080FHD/720P/VGA. Higher resolutions will
give you a sharper image, but take up more memory on the card.
Display Mode: Picture in Picture /Front Camera /Rear Camera/Split-screen
Loop Recording: Off/1 Minutes/3 Minutes/5 Minutes
If you set this Off, Once the memory card is full, the camera will stop
recording. If you select 1 Minutes /3 Minutes/5 Minutes as the
duration of recording length for the individual video files, and the
·
·
·
·
·
·
driving recorder will fill the SD card then loop back to the beginning,
overwriting the oldest unlocked file.
WDR: Wide Dynamic Range--The ratio of the brightest luminance
signal value to the darkest light signal value that can be resolved.
Present a crisp and clear picture quality with harmonious contrast in a
high contrast, high discrepancy environment.
Setting to ON mode is recommended.
Exposure: Adjust exposure level for different light levels
+3/+2/+1/0/-1/-2/-3
Record Audio: Enable or disable sound recording with the video.
Off--when Setting it to OFF, sound will not be recorded.
On--when Setting it to ON, sound will be recorded.
Date Stamp: Turn On/Off the time and date stamp shown on recorded
files.
OFF--When setting it to OFF, no data stamp will be shown on the
recorded files.
ON--When setting it to ON, data stamp will be shown on the recorded
files.
License plate number: It will be shown on the video file. Press
“Record/OK" button to enter the car NO. setting. Press “UP" and
“Down" to select from A to Z and 0 to 9. Then press “Menu" button to
the next one. Press “Record/OK" button to save and exit. When
finished, it will be shown on the LCD display.
GPS: Records the track of the car accurately.
Set the GPS to on and plug the GPS module(3.5mm plug) into the GPS
Port on the right side of the unit. There is speed shown on the lower
right of the screen.
Warm tips:
a. GPS module is not included.
b. It needs software to playback video. Please download the software:
“Registrator Viewer".
Speed unit: Select the speed unit you need, Km/H, Mile/H.
Setting Menu:
In the recording status, press the “Record/OK" button to suspend the
video, and then press twice the “Menu" button to enter the Setting
Menu.
Date/Time: Press “Record/OK" button to enter the date/time setting,
Press “Up" and "Down" buttons to set numbers, Press “Menu" button
to enter the setting of the next number. After setting the right
numbers, press the “OK" button to save the setting and exit.
Screen savers: If it is recording and set the screen saver to 1/2/3
minutes, the display will go off while the dash camera continues
recording and the screen can be woken up at any time by pressing any
button. If turn Off, the screen will always light on when it is recording.
Auto Power Off: Please make sure the dash cam is not recording.
Choose Off--When not recording, no operation, no action, it will not
automatically shut down.
Choose 1 Minute/3 Minutes/5 Minutes--When not recording, no
operation, no action, it will automatically shut down 1 Minute/3
Minutes/5 Minutes later.
Frequency: Press “Up" and “Down" to select the frequency
(50Hz/60Hz)you need, Press “Record/OK" button to save and exit.
Beep Sound: Turns the sound on or off for each time a button is
pressed.
Note: this only affects normal button presses.
Language: Press “Record/OK" button to enter the language setting.
Press “Up" and “Down" to select the language you need. Press
“Record/OK" button to save and exit, it allows you to set the language
for the device from among the 9 supported languages.
Format: Allow you to delete the SD card’s all data.
Cancel: Do not format the SD card.
OK: Format the SD card.
Note: Before formatting the SD card, please back up your data if you
need.
Default Setting: If there is a set error, you can use this to return menu
setting to defaults. After you have returned to the default setting, all
the setting will return to the factory setting. And you need set the
date/time, auto power off, Motion detection and so on.
Version: Display the information of the version.
To Next Page
Loading...
