To Next PageTo Next PageWhat to do if my ApooDr Air Conditioner is not working?
If your ApooDr Air Conditioner isn't working, consider these possible causes: * Power failure: Wait for the power to be restored. * Power is off: Turn the power on. * Blown fuse: Replace the fuse. * Dead remote control batteries: Replace the batteries. * Unit's 3-minute protection activated: Wait three minutes after restarting the unit. * Timer activated: Turn the timer off.
Why does my ApooDr ASF16-12H1A start and stop frequently?
Frequent starting and stopping of your ApooDr Air Conditioner can be due to: * Too much or too little refrigerant: Check for leaks and recharge the system with refrigerant. * Incompressible gas or moisture in the system: Evacuate and recharge the system with refrigerant. * Broken compressor: Replace the compressor. * Voltage issues: Install a manostat to regulate the voltage.
Why is my ApooDr Air Conditioner not cooling properly?
Several factors can cause poor cooling performance in your ApooDr Air Conditioner. These include: * Temperature setting being too high: Lower the temperature setting below the ambient room temperature. * Dirty heat exchanger: Clean the heat exchanger on the indoor or outdoor unit. * Dirty air filter: Remove and clean the air filter according to the instructions. * Blocked air inlet or outlet: Turn off the unit, remove any obstructions, and turn it back on. * Open doors and windows: Ensure all doors and windows are closed during operation. * Excessive heat from sunlight: Close windows and curtains during periods of high heat. * Too many heat sources: Reduce the number of heat sources in the room. * Low refrigerant: Check for leaks, reseal if necessary, and top off the refri...
Essential warnings for safe operation and potential hazards.
Safety guidelines to follow before and during cleaning or maintenance.
Crucial warnings and regulations regarding electrical connections and safety.
Safety precautions to prevent damage or injury during installation.
Information and handling notes for refrigerants like greenhouse gasses.
Safety requirements and precautions when using specific refrigerants.
Proper disposal methods for electrical equipment according to EU regulations.
Explains various indicators and displays on the indoor unit's panel.
Defines the optimal room and outdoor temperatures for different modes.
Details additional functionalities like Auto-Restart, Anti-mildew, Wireless Control.
How to use the SLEEP function to optimize energy use during sleep.
Guidance on adjusting vertical and horizontal airflow angles for comfort.
Instructions for operating the unit manually when the remote is lost.
Step-by-step guide for cleaning the indoor unit's exterior and filters.
Procedure for cleaning the air filters to maintain cooling efficiency.
Explains the filter cleaning and replacement reminders displayed by the unit.
Steps to take for proper storage when the unit is not used for an extended time.
Recommended checks before starting regular use after a period of inactivity.
Lists common problems and their possible causes and solutions.
Important checks and information before starting indoor unit installation.
Guidelines for choosing the optimal and safe location for the indoor unit.
Instructions for securely attaching the indoor unit's mounting plate to the wall.
Detailed steps for drilling the wall hole for unit connections.
Guidance on preparing the refrigerant piping before passing it through the wall.
Instructions for correctly connecting the drain hose for proper water drainage.
Procedures for safely connecting signal and power cables between units.
How to bundle and protect piping, drain hose, and cables for installation.
Steps for securely mounting the indoor unit onto the installed mounting plate.
General instructions and considerations for outdoor unit installation.
Guidelines for choosing the optimal and safe location for the outdoor unit.
Procedure for installing the drain joint on the outdoor unit, especially for heat pumps.
Instructions for securely anchoring the outdoor unit to its base or bracket.
Procedures for safely connecting signal and power cables to the outdoor unit.
Explains how pipe length affects performance and efficiency.
Detailed steps for connecting refrigerant pipes properly and safely.
How to correctly cut refrigerant pipes to the required length and angle.
Procedure for removing burrs from cut pipe ends to ensure an airtight seal.
Instructions for properly flaring pipe ends to create an airtight connection.
Guidance on safely connecting the flared pipes to the unit's valves.
Detailed steps for connecting refrigerant pipes to the indoor unit.
Detailed steps for connecting refrigerant pipes to the outdoor unit.
Important steps and precautions before performing air evacuation.
Step-by-step guide for using a vacuum pump and manifold gauge for evacuation.
Information on calculating and adding refrigerant based on pipe length.
Checks to perform before the initial test run for safety and proper function.
Verifying the electrical system is safe and correctly installed.
Methods for detecting refrigerant leaks at connection points.
Steps for performing a comprehensive test run of the air conditioning unit.
Re-checking refrigerant pipe connections after the unit has run.
General| Cooling Capacity | 16000 BTU/h |
|---|---|
| Voltage | 220-240V |
| Refrigerant | R410A |
| Type | Split System |
| Frequency | 50Hz |
| Power Supply | Single Phase |
