Aqua Products S2 User Manual

QUICK START
ITEM: 820001
Thank You
Thank You for entrusting us with keeping your pool clean. We strive
to enhance your pool experience by keeping your pool environment
healthy for you, your family and your friends. Please read this Quick
Start Manual in its entirety to ensure proper operation and care of your
cleaner. Please feel free to leave a review online.
IMPORTANT:
PLEASE READ BEFORE OPERATING CLEANER
• SAFETY INSTRUCTIONS
• WHAT TO EXPECT
• QUICK START
QUICK START OPERATOR MANUAL
FOR THE FOLLOWING CLEANERS
FOR YOUR RECORDS, PLEASE KEEP A COPY OF YOUR
SERIAL NUMBER AND DATE OF PURCHASE HERE
• POWER SUPPLY
• HOW TO GUIDE
• TROUBLESHOOTING

Aqua Products S2 Specifications

General

Pool Type	In-Ground
Type	Robotic
Power Source	Electric
Warranty	2 Years
Cleaning Coverage	Bottom, Walls, Waterline
Cable Length	60 ft

Summary

WARNINGS & SAFETY PROCEDURES

OPERATION AND STORAGE TEMPERATURES

Specifies proper temperature ranges for operation and storage to protect components.

USE OF THE CLEANER IN A VINYL LINER POOL

Details potential pattern removal on vinyl liners and manufacturer's liability.

WHAT TO EXPECT

YOUR ROBOT'S TYPICAL CLEANING METHOD

Explains the cleaner's path and coverage based on pool floor-to-wall transitions.

CLEANER'S MOVEMENT

Describes the back/forth motion and how axle positioning affects turns.

CLEANER'S PERFORMANCE

Highlights vacuuming rate and the importance of clean filter bags.

IMPORTANT: OPENING YOUR POOL

Recommends manual cleaning before first use after off-season to avoid fast filter clogging.

QUICK START

POWER SUPPLY OPERATION

STANDARD POWER SUPPLIES

Details operation of standard power supplies with ON/OFF and SELECT buttons.

STANDARD POWER SUPPLY + EXTERNAL RUN BUTTON FEATURE

Explains how to use the external run button with timers for scheduled operation.

HOW TO...

ENSURE POOL COVERAGE & PREVENT CABLE TANGLING

Guides on adjusting axle pins for optimal coverage and preventing cable tangles.

CLEAN THE FILTERS

Step-by-step instructions for removing and cleaning filter bags or baskets.

RETRIEVE CLEANER FROM POOL

Instructions on safely pulling the cleaner from the pool using the cable or handle.

CABLE DETANGLER

Explains how to use the cable detangler feature to straighten the floating cable.

EXTEND THE LIFE OF YOUR CLEANER

TIP #1: DO NOT DROP THE UNIT OR POWER SUPPLY!

Warns against dropping the cleaner or power supply to avoid damage.

TIP #2: CLEAN THE FILTER BAGS!

Emphasizes regular cleaning of filter bags/baskets for optimal performance and water clarity.

TIP #3: POOL COVERAGE / PREVENT CABLE TANGLING

Recommends adjusting axle pins for full pool coverage and tangle prevention.

TIP #4: GIVE IT A RINSE

Advises rinsing the cleaner after each use to remove chlorine and prolong its life.

TIP #5: STORAGE WHEN NOT IN USE

Provides guidelines for proper dry storage in a shaded area, including winter storage temperatures.

TROUBLESHOOTING

MOVES SLOWLY OR DOESN'T SEEM TO BE VACUUMING

Solutions for slow movement or poor vacuuming, focusing on filter bag cleanliness and suction ports.

ALL LED LIGHTS ARE BLINKING ON THE POWER SUPPLY

Identifies causes for blinking LEDs, such as unit out of water or stuck components.

THE FLOATING CABLE IS COILED UP

Offers solutions for a coiled cable, including axle adjustment and using the detangler.

UNIT IS NOT SUCKING UP DEBRIS

Troubleshooting steps for lack of suction, covering setup, propeller, suction ports, and filter bags.

UNIT IS STUCK IN THE MIDDLE OF THE POOL BUT THE UNIT STILL PUMPS OUT WATER

Addresses issues with the unit getting stuck, checking for obstructions or suction port height.

UNIT LOOKS LIKE IT IS MOVING IN THE SAME AREA OF THE POOL AND DOES NOT CLEAN OTHER AREAS

Solutions for poor pool coverage, involving axle adjustment and starting location.

UNIT DOES NOT COVER THE ENTIRE POOL

Steps to ensure full pool coverage, checking filter bags, timing cycles, and pin configuration.