Aqua Products Splasher

Questions and Answers

C
Crystal JordanAug 16, 2025
Why does my Aqua Products Swimming Pool Vacuum SPLASHER not move?
- L
  luke90Aug 16, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) is not moving or moves very slowly, several factors could be responsible. First, ensure your pool's filtration system provides sufficient suction and has been backwashed recently. Check all baskets (pump and weir) and the diaphragm for any debris. Inspect the SPLASHER diaphragm for wear and replace it if needed. Look for leaks in the hoses, indicated by air bubbles at the return line. Also, verify the outer tube/outer extension pipe clearance is within +/- 3/4". If the sand in the filter is older than +/- 3 years, consider changing it or cleaning the filter cartridge. Finally, make sure the vacuum lid sits flush in the weir; replace it if damaged.
J
Joanna RamirezAug 18, 2025
How to improve climbing for my Aqua Products Splasher?
- K
  Kimberly GriffinAug 18, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) isn't climbing, start by ensuring the baskets and cleaner are free of debris, maximizing water flow, and backwashing the filter. Confirm adequate suction and adjust the flow control valve settings higher. The sand or filter cartridge may need changing or backwashing. Check if the disc is curling and needs replacement. Ensure the pool radius is sufficient (at least 300mm) for wall climbing. Also, check the float chamber for buoyancy, ensuring no water is present, and inspect the outer tube or outer extension pipe for excessive wear (over 2mm play), replacing if necessary.
N
Nicole MoodyAug 22, 2025
How to check suction for Aqua Products Splasher?
- E
  Elizabeth GarrettAug 22, 2025
  To address suction issues with your Aqua Products Swimming Pool Vacuum, first, ensure your pool's filtration system provides sufficient suction and operates according to the manufacturer's instructions. Backwash the filter if necessary to improve water flow. If suction is strong, verify the flow control valve functions correctly. Also, check for leaks in the hoses and ensure they're properly connected.
R
Renee CalderonAug 25, 2025
What to do if Aqua Products Splasher Swimming Pool Vacuum moves a short distance and stops?
- C
  Crystal MartinezAug 26, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) moves a short distance and then stops, refer to the solutions for when the SPLASHER does not move. Also, the outer tube or outer extension pipe might be worn out. The pump suction may be too strong, causing the unit to stick to the floor; adjust the flow control valve so the gate opens more easily to bypass water. A normal setting is between 2 and 4.
A
Amanda RichardsAug 28, 2025
Why is Aqua Products Splasher sticking on pool stairs?
- J
  James LeeAug 28, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) is sticking on pool stairs, try adjusting your pool’s return flow / aimflow to guide the cleaner away from the steps. Verify proper hose length and the correct position of the hose weight(s). You might also remove or add one hose section. Also, using your flow control valve, increase or decrease the flow to your SPLASHER within the maximum/minimum range.
T
Timothy JonesAug 30, 2025
How to prevent Aqua Products Swimming Pool Vacuum from getting stuck?
- F
  Francis FinleyAug 30, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) gets stuck in a particular place, adjust the hose length by adding or removing a hose. Ensure the aimflow nozzle isn't interfering with movement; if so, adjust it to direct flow away from the unit. If the problem persists, attach The Easy-Out Jogger on the first hose and insert an aimflow diverter ball in the aimflow nozzle.
K
Kristin ClaySep 2, 2025
How to stop Aqua Products Splasher Swimming Pool Vacuum from climbing out of the water?
- K
  Kathleen BallSep 3, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) climbs out of the water, ensure the flow control valve is working and free of debris. Also, lower the setting on the flow control valve to reduce water flow through it and increase the bypass flow.
A
Andrea OrtizSep 6, 2025
What to do if Aqua Products Splasher falls on its side?
- E
  ecarterSep 6, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) falls on its side, check if the float is filled with water and ensure that the outer extension pipe can rotate freely.
S
Steven Davis MDSep 8, 2025
Why is Aqua Products Splasher Swimming Pool Vacuum moving in a set pattern?
- V
  Victoria BrownSep 9, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) is moving in a set pattern, ensure the hose length is correct by adding or removing sections. Also, make sure the hoses are in good condition, not coiled or bent, and always store them in a straight position.
F
fbrownSep 12, 2025
Why Aqua Products Swimming Pool Vacuum does not sink?
- D
  Diana SummersSep 12, 2025
  If your Aqua Products Swimming Pool Vacuum (SPLASHER) does not sink, make sure there is no air trapped in the hoses or unit, and ensure that the SPLASHER has its weight in the unit.

Summary

Product Overview

Features and benefits of your SPLASHER

Lists the key features and advantages of the SPLASHER pool cleaner.

Important Warnings and Safety Information

How to safely operate the SPLASHER Automatic Pool Cleaner

Provides essential safety guidelines for the installation, operation, and maintenance of the cleaner.

General Installation Checks

Pre-Installation Check List

A list of checks to perform before installing the SPLASHER cleaner to ensure proper setup.

Post-installation Check List

Items to verify after installing the SPLASHER to ensure correct operation.

General Installation Checks: Preparation

Preparation for installation (Pool preparation)

Steps to prepare the pool and filtration system before installing the SPLASHER cleaner.

Method for cleaning pools and pumps

Details on how to prepare the pool and pump system for cleaner operation.

SPLASHER Components

SPLASHER Components and Spare Parts diagram

Identifies all components of the SPLASHER and provides a spare parts diagram.

SPLASHER Assembly

Hose Assembly

Attaching Hose Weights

Installation

Cleaning line installation

Instructions for installing the cleaner hose and connection to the pool's filtration system.

Weir installation

Guidance on how to install the cleaner hose connection at the pool's weir.

Connecting your SPLASHER

Adjustments

Flow Control Valve

Details on how to adjust the flow control valve for optimal SPLASHER operation.

Maintenance

Diaphragm Assembly

Step-by-step instructions for assembling the diaphragm unit of the SPLASHER.

Routine Maintenance

Covers cleaning, wear and tear checks, and hose maintenance for the SPLASHER.

Tips

Provides practical advice for using and maintaining the SPLASHER pool cleaner.

Troubleshooting

SPLASHER does not move OR moves very slowly

Solutions for when the SPLASHER is not moving or moves at a very slow speed.

Suction

Troubleshooting steps related to insufficient or excessive suction affecting the cleaner.

SPLASHER moves a short distance then stops.

Addresses issues where the SPLASHER stops moving after a short period.

SPLASHER falls on its side

Troubleshooting tips for when the SPLASHER repeatedly falls on its side.

Troubleshooting

SPLASHER gets stuck in a particular place

Solutions for common problems where the SPLASHER gets stuck in specific areas.

SPLASHER does not sink

Troubleshooting steps if the SPLASHER fails to sink to the pool floor.

SPLASHER does not climb

Addresses issues where the SPLASHER is unable to climb pool walls or surfaces.

SPLASHER climbs out of the water

Solutions for when the SPLASHER excessively climbs out of the water.

Troubleshooting

SPLASHER is sticking on pool stairs

Tips for preventing the SPLASHER from getting stuck on pool stairs.

SPLASHER is moving in a set pattern

Troubleshooting steps for when the SPLASHER moves in a repetitive or fixed pattern.

Diaphragm Assembly

Refers to the Maintenance section for issues related to diaphragm assembly.

Customer Care

Warranty Information

SPLASHER 1 Year Manufacturers Warranty

Details of the manufacturer's one-year limited warranty for the SPLASHER cleaner.

Warranty Exclusions

Lists specific conditions and situations not covered by the SPLASHER warranty.

Warranty Terms and Conditions

Conditions & Exclusions

Outlines the specific terms and exclusions applicable to the SPLASHER warranty.

Warranty Card Submission

Notes