Arcam Delta 70.2 User Manual

9 PREVIOUS TRACK button
This button selects the track number by counting down the
displayed digits.
10 NEXT TRACK button
This button selects the track number by counting up the
displayed digits.
in general the TRACK buttons are used to find the track
number
you
want
to
start
with
and
for
selecting
track
numbers
when
compiling
a
program.
They
can
also
be
used
for
returning
to
a
previous
track
number
or
for
moving
on
to
a
later
one
while
the
disc
is
playing.
11 PROGRAM button
This button stores the track numbers of a program (up to 20
tracks
in
any
order
may
be
stored)
and
also
produces
a
sequential
display
(review) of the stored program.
12 REPEAT button
This button repeats a whole disc or selected program.
13 REM/LAP button
This button switches between displays indicating the
remaining
(REM)
time
of
a
disc
and
the
elapsed
[LAP)
time
of
the
track
playing.
14 DISPLAY Control
This control adjusts the brightness of the display.
The switch has three positions:
Fully clockwise — Normal
Centre — Dimmed
Fully anti-clockwise — Off
It has been observed that a better sound can be achieved
when the display is either dimmed or is completely off.
Visual Displays
(A) Power on LED
Glows green when mains power is applied and the player is
switched on.
(B) Main Display
This comprehensive display indicates all the information
necessary
for
the
operation
of
your
machine.
The
basic
display
indicates
track numbers, index numbers and all timing details in minutes and
seconds.
The display also indicates in detail which of the machine's
various
functions
are
in
operation.
Headers
denoting
REPEAT,
PAUSE,
REVIEW,
PROGRAM,
REM/LAP
time,
DISC
and
ERROR
appear
around
the basic display when a particular function is being used.
Operating the Player
Mains power
The player is turned on by depressing the POWER switch (1).
The
adjacent
power
LED
(A)
will
glow
green.
The
display
{B}
will
light
up,
assuming
the
display
control
knob
is
in
the
on
or
dimmed
position.
if there is no disc in the machine at switch on, the DISC
header
on
the
display
will
flash
for
a
few
seconds,
the
ERROR
header
will
light
up
(signifying
that
there
is
no
disc
to
play)
and
the
display
will
indicate a series of noughts.
if there is a disc in the machine the DISC header will flash for
a
few
seconds
before
the
display
indicates
the
total
number
of
tracks
on
and total playing time of the disc.
Loading and Unloading
Push
the
LOAD
button
(3)
once
to
open
the
disc
loading
drawer.
Ensure
the
drawer
is
not
obstructed.
Holding
the
disc
horizontally
by
the
edge
place
it,
label
side
up,
in
the
drawer
—
make
sure
the
disc
is
properly
in
place
or
else
it
may
be
damaged
when
the
drawer
is
closed.
Push
the
LOAD
button
{3)
once
again
or,
if
preferred,
push
in
the
drawer
mechanism
approx.
1/4”
(6mm)
to
activate
the
drawer
motor.
Once
the
disc
is
in
the
player
the
DISC
header
will
glow
for
a
few
seconds
and
then
the
display
will
indicate
the
number
of
tracks
on
and
the
total
playing
time
of
the
disc.
To
unload
the
disc
press
the
LOAD
button
(3)
and
when
the
tray
is
fully
out
remove
the
disc.

Arcam Delta 70.2 Specifications

General

Brand	Arcam
Model	Delta 70.2
Category	CD Player
Language	English