AREBOS AR-HE-SPA6RAH - User Manual

Questions and Answers

J
Jessica MccormickAug 18, 2025
Why is the control panel showing a high temperature reading on my AREBOS AR-HE-SPA6RAH Swimming Pool?
- M
  Melissa NewmanAug 18, 2025
  If the control panel of your AREBOS Swimming Pool shows a high temperature reading, it might be due to a small amount of residual water surrounding the heating element. Activate your filter to allow the water to circulate inside your hot tub. It can also be caused by a blockage caused by limescale build up, a dirty filter or a seized impellor, so ensure that there is no blockage.
J
Jennifer LopezAug 21, 2025
What to do if my AREBOS Swimming Pool displays error code HL?
- D
  Dana EvansAug 21, 2025
  If you see the error code HL on your AREBOS Swimming Pool, it indicates a blockage preventing water circulation around the pump and heating system. Check the water flow from the filter outlet. It could also be due to a dirty filter, a blocked impeller, or limescale buildup. Ensure your filter is clean and doesn’t need replacing. In the event that debris has been drawn into the motor, turn off the hot tub at the mains. If the cause is limescale build up, conduct a descaling routine into your hot tub maintenance schedule.
C
clarkrachelAug 23, 2025
Why is the heating system not working in my AREBOS AR-HE-SPA6RAH Swimming Pool?
- L
  Lindsey RobertsAug 23, 2025
  If your AREBOS Swimming Pool's heating system isn't working, start by ensuring the temperature is set high enough (20-40°C). A dirty filter cartridge can also be the culprit, so replace it. Check that the water level isn't too low and top it up if needed. If dirt accumulates inside the motor, remove the filter cartridge, place the water hose at the water outlet, and use a cloth bag to collect dirt particles at the filter connection while flushing the motor. If the issue persists, it may be due to the heating element being defective, or the power voltage being too low or the frequency incorrect. In these cases, contact customer service or a qualified electrician, respectively.
C
changlaurenAug 26, 2025
How to clean the water in my AREBOS Swimming Pool?
- T
  Tiffany CameronAug 26, 2025
  If the water in your AREBOS Swimming Pool is not clean, increase the filter time. The filter cartridge may be dirty, so replace or clean it. Also, ensure you are using the correct water treatment by following the chemical manufacturer's instructions.
W
Wendy HooverAug 28, 2025
Why is the filter system not working in my AREBOS AR-HE-SPA6RAH Swimming Pool?
- J
  Joyce PerryAug 28, 2025
  If your AREBOS Swimming Pool's filter system isn't working, the filter cartridge might be dirty, so replace it. Also, ensure the water level is sufficient and top it up if necessary.
E
Erin AnthonyAug 30, 2025
What does error code FC mean on my AREBOS Swimming Pool?
- E
  Erik GreenAug 30, 2025
  If you see the error code FC on your AREBOS Swimming Pool, the filtration system has been running for approximately 168 hours, which means you should check your filter. Make sure the filter is clean and change it if necessary.
E
Erik LucasSep 1, 2025
What does error code SL mean on my AREBOS AR-HE-SPA6RAH Swimming Pool?
- A
  Adrian CruzSep 1, 2025
  If you see the error code SL on your AREBOS Swimming Pool, it's likely due to a blocked or dirty filter, or a low ambient temperature. Make sure the filter is clean and replace it if necessary.
J
Jeanette TorresSep 3, 2025
Why is the filter pump so noisy in my AREBOS AR-HE-SPA6RAH Swimming Pool?
- G
  griffithtylerSep 4, 2025
  If your AREBOS Swimming Pool's filter pump is noisy, the filter cartridge or the filter cover might be dirty. Replace the filter cartridge and clean the filter cover. Also, ensure the water level is adequate and fill it up if it's too low.
E
Elaine EllisSep 6, 2025
Why is the jet/bubble system not working on my AREBOS AR-HE-SPA6RAH?
- K
  Kyle BrewerSep 6, 2025
  If the jet/bubble system is not working on your AREBOS Swimming Pool, the air pump may be overheating. Wait until the air pump has cooled down, then press the BUBBLE button to activate the function.
J
Joseph ChambersSep 8, 2025
What to do if the LED light doesn’t work on my AREBOS AR-HE-SPA6RAH Swimming Pool?
- C
  Courtney CarpenterSep 8, 2025
  If the LED light on your AREBOS Swimming Pool doesn't work, first ensure you have removed the clear tab from the remote control. Check that the connection points are aligned correctly on the receiver. If the remote-control battery is not working, replace it with a new 1 x 3v CR2025 Lithium Battery. If the LED lighting is too tight between the loops, refit the LED Lights loosely to allow the hot tub to expand once filled with water, making sure that the position of the LED faces the base of the pool.