AREBOS AR-HE-SPA6SLH - User Manual

Questions and Answers

R
Raymond ThorntonAug 18, 2025
Why is the control panel showing a high temperature reading on my AREBOS AR-HE-SPA6SLH Swimming Pool?
- T
  Tracy AllenAug 18, 2025
  If the control panel of your AREBOS Swimming Pool shows a high temperature reading, it might be due to a small amount of residual water surrounding the heating element. Activate your filter to allow the water to circulate inside your hot tub. It can also be caused by a blockage caused by limescale build up, a dirty filter or a seized impellor, so ensure that there is no blockage.
W
Walter HowardAug 20, 2025
What to do if my AREBOS Swimming Pool displays error code HL?
- A
  Andrew AlvarezAug 21, 2025
  If you see the error code HL on your AREBOS Swimming Pool, it indicates a blockage preventing water circulation around the pump and heating system. Check the water flow from the filter outlet. It could also be due to a dirty filter, a blocked impeller, or limescale buildup. Ensure your filter is clean and doesn’t need replacing. In the event that debris has been drawn into the motor, turn off the hot tub at the mains. If the cause is limescale build up, conduct a descaling routine into your hot tub maintenance schedule.
V
Vicki BrayAug 23, 2025
Why is the heating system not working in my AREBOS AR-HE-SPA6SLH Swimming Pool?
- M
  Matthew McintoshAug 23, 2025
  If your AREBOS Swimming Pool's heating system isn't working, start by ensuring the temperature is set high enough (20-40°C). A dirty filter cartridge can also be the culprit, so replace it. Check that the water level isn't too low and top it up if needed. If dirt accumulates inside the motor, remove the filter cartridge, place the water hose at the water outlet, and use a cloth bag to collect dirt particles at the filter connection while flushing the motor. If the issue persists, it may be due to the heating element being defective, or the power voltage being too low or the frequency incorrect. In these cases, contact customer service or a qualified electrician, respectively.
M
Michelle JonesAug 26, 2025
How to clean the water in my AREBOS AR-HE-SPA6SLH?
- M
  Molly WashingtonAug 26, 2025
  If the water in your AREBOS Swimming Pool is not clean, increase the filter time. The filter cartridge may be dirty, so replace or clean it. Also, ensure you are using the correct water treatment by following the chemical manufacturer's instructions.
M
Maria JohnsonAug 27, 2025
Why is the filter system not working in my AREBOS AR-HE-SPA6SLH?
- L
  lrogersAug 28, 2025
  If your AREBOS Swimming Pool's filter system isn't working, the filter cartridge might be dirty, so replace it. Also, ensure the water level is sufficient and top it up if necessary.
J
Julie NixonAug 30, 2025
What does error code FC mean on my AREBOS Swimming Pool?
- E
  escobartinaAug 30, 2025
  If you see the error code FC on your AREBOS Swimming Pool, the filtration system has been running for approximately 168 hours, which means you should check your filter. Make sure the filter is clean and change it if necessary.
M
Mrs. Maria FarmerSep 1, 2025
What does error code SL mean on my AREBOS AR-HE-SPA6SLH?
- M
  mauricecohenSep 1, 2025
  If you see the error code SL on your AREBOS Swimming Pool, it's likely due to a blocked or dirty filter, or a low ambient temperature. Make sure the filter is clean and replace it if necessary.
H
Harry SimsSep 3, 2025
Why is the filter pump so noisy in my AREBOS Swimming Pool?
- S
  Sarah GreenSep 3, 2025
  If your AREBOS Swimming Pool's filter pump is noisy, the filter cartridge or the filter cover might be dirty. Replace the filter cartridge and clean the filter cover. Also, ensure the water level is adequate and fill it up if it's too low.
E
emily82Sep 5, 2025
Why is the jet/bubble system not working on my AREBOS AR-HE-SPA6SLH Swimming Pool?
- J
  jkennedySep 6, 2025
  If the jet/bubble system is not working on your AREBOS Swimming Pool, the air pump may be overheating. Wait until the air pump has cooled down, then press the BUBBLE button to activate the function.
L
Lauren DyerSep 8, 2025
What to do if the LED light doesn’t work on my AREBOS AR-HE-SPA6SLH Swimming Pool?
- M
  Michael LawsonSep 8, 2025
  If the LED light on your AREBOS Swimming Pool doesn't work, first ensure you have removed the clear tab from the remote control. Check that the connection points are aligned correctly on the receiver. If the remote-control battery is not working, replace it with a new 1 x 3v CR2025 Lithium Battery. If the LED lighting is too tight between the loops, refit the LED Lights loosely to allow the hot tub to expand once filled with water, making sure that the position of the LED faces the base of the pool.

Summary

Safety Instructions

Specific Safety Instructions

Provides detailed safety guidelines for using the spa pool.

Child Safety Precautions

Details measures to ensure child safety around the spa.

Electrical Safety and Shock Hazards

Warns about electrical hazards and proper grounding.

Health Risks Associated with Use

Outlines health risks like hyperthermia and recommendations for pregnant women.

Installation

Choosing a Safe Installation Location

Details unsuitable locations and requirements for the installation surface.

Spa Pool Assembly Steps

Provides step-by-step instructions for assembling the spa pool.

Filling the Spa Pool with Water

Instructions on how to fill the spa pool with water correctly.

Connecting to the Power Supply

Details on connecting the spa to the mains power, including RCD testing.

Cleaning, Maintenance and Storage

Water Treatment and Parameter Balancing

This document is the original user manual for the AREBOS SPA Pool, providing comprehensive information on its safety, installation, operation, maintenance, and disposal.

Function Description:

The AREBOS SPA Pool is an inflatable hot tub designed for private use, offering relaxation and hydrotherapy. It features a heating system, a filter pump for water circulation and purification, and an air blower for a jet/bubble massage system. Some models also include LED lighting for enhanced ambiance. The spa is designed to be easily inflatable and portable, suitable for both indoor and outdoor use, provided the installation guidelines are followed.

Important Technical Specifications:

The manual details various SPA Pool types with different models (CORFU, PALMA, TENERIFE, SANTORINI, BALI, MONACO, FLORENCE, GRANADA, BARCELONA, ROME, BERGEN, VENICE), each having specific dimensions and capacities. Key specifications include:

Engine Power (heater): 1800 W for all models.
Engine Power (air blower): 600 W for all models.
Power Supply: AC 220-240V / 50Hz.
Filter Pump Power: 12 V / 30 W for all models.
Flow Rate: 1400 l/h for all models.
Temperature Increasing Rate: 1.0-2.0°C / hour for all models.
Cable Length: 5 m for all models.
User Capacity/Seating Capacity: Varies from 2 persons (BERGEN) to 6 persons (TENERIFE, SANTORINI).
Max. Water Capacity: Ranges from 550L (BERGEN) to 1000L (SANTORINI).
Temperature Range: 20°C - 40°C for all models.
Number of Massage Jets: Varies from 90 (BERGEN) to 130 (TENERIFE, SANTORINI).
Pool Size (external): Ranges from 154x154cm (CORFU, MONACO) to Ø208cm (SANTORINI).
Pool Size (internal): Ranges from 114X114cm (CORFU, MONACO) to Ø168cm (SANTORINI).
Height of the Pool: 65cm for all models.
Form: Includes square, round, oval, and octagonal shapes.
Net Weight: Varies from 22 kg (CORFU, PALMA, BERGEN) to 26 kg (TENERIFE, SANTORINI).

The device is built according to current safety regulations and includes a residual current device (RCCB) for electrical safety.

Usage Features:

Installation: Requires a stable, horizontal surface capable of bearing at least 360 kg/m², with a functional drainage system. The spa should not be exposed to direct sunlight for prolonged periods to prevent deformation.
Inflation: The spa is inflated using the BUBBLE button on the control panel. It should be inflated until the upper edge can be pressed in by approximately 4-5 cm.
LED Lighting (where applicable): Models with LED lighting require the LED strip to be inserted into tabs at the bottom of the pool, facing the base. The lighting is controlled by a remote, offering different colors, brightness, and modes.
Water Filling: Fill with fresh tap water to the marked level. Do not overfill. Seawater or salt water should not be used.
Control Panel: Features buttons for FILTER (ON/OFF filter system), BUBBLE (ON/OFF jet system), HEATER (ON/OFF heating system), and SET TEMP (temperature adjustment).
Heating System: Operates between 20-40°C. The heating system automatically activates the filter pump. It may take 12-24 hours to reach the desired temperature, depending on ambient and mains water temperature.
Jet System: The bubble system runs for 20 minutes automatically and can be restarted after a 10-minute wait.
Safety Precautions: Emphasizes child safety (supervision, covers), electrical safety (grounding, no extension cords, qualified electrician for repairs), and health risks (water temperature limits, advice for pregnant women and individuals with health conditions, no alcohol/drugs during use). Hyperthermia risks are detailed. The pool should not be operated below 4°C or in the rain.

Maintenance Features:

Draining: Water can be drained using a submersible pump or by unscrewing the end cap of the water outlet and attaching a filling hose. The BUBBLE button can be pressed for 2-3 minutes to drain water from the air line.
Filter Cartridge: Needs to be checked and cleaned after each use. It should be changed every 3 days or when dirty/discolored. Used filters can be cleaned in an empty dishwasher or washing machine (in a pillowcase/towel).
Water Treatment: Regular checking of pH (7.2-7.8), free chlorine (3-5 ppm), and total alkalinity (80-120 mg/l) is crucial. Water treatment products (chlorine granules/tablets, pH plus/minus granules) should be added to the middle of the pool with air jets and heater on. A dosing float should be used for chemicals.
Cleaning the Pool: Clean with soap, water, a damp cloth, and a soft brush. Avoid hard brushes or abrasive products.
Repairs: Small holes or punctures can be repaired using supplied patches and adhesive.
Winter Storage: Drain all water, remove the filter cartridge, clean and dry the spa, expel all air, and fold loosely. Store in a dry, frost-free place. Improper storage in sub-zero temperatures can damage the pool and invalidate the warranty.
Troubleshooting: The manual provides a detailed troubleshooting guide for common issues such as non-working jet/bubble or heating systems, noisy filter pump, air leakage, water leakage, deformation, unclean water, and LED light malfunctions. Error codes (HL, SH, FC, SL) are explained with corresponding solutions, including checking water flow, cleaning filters, and contacting customer service. A manual reset button is available for overheating protection.

The document concludes with environmentally friendly disposal instructions for the product and packaging, as well as contact information for customer service and the EU Declaration of Conformity.