Ariens 915163 User Manual (English)

Questions and Answers:

P
phobbsAug 13, 2025
Why Ariens 915163 engine will not crank/start?
- L
  Larry OwensAug 14, 2025
  There are several potential reasons why your Ariens Lawn Mower engine won't crank or start: * The safety interlock system might not be engaged or could be faulty. Ensure it is properly engaged. * The fuel tank might be empty. Refill the fuel tank. * The battery might be discharged. Charge the battery. * There might be a poor connection between the battery and battery cables. Tighten or clean the battery cables. * Spark plug wires might be loose, or the spark plugs could be faulty. Connect the wires or replace the spark plugs. * The electrical system or the engine might be faulty.
J
John CunninghamAug 17, 2025
What to do if Ariens 915163 PTO or mower blades do not engage or shuts off?
- A
  anthonyreevesAug 18, 2025
  If the PTO or mower blades on your Ariens Lawn Mower do not engage or shut off, consider these possible causes: * The operator presence switch may not be depressed. Make sure you are sitting on the seat to depress it. * The electric clutch connector might be loose or disconnected. Connect the electric clutch connector. * The PTO belt could be faulty. Replace the PTO belt.
R
Robert RuizAug 21, 2025
Why Ariens 915163 Lawn Mower engine runs rough?
- B
  Brandon RoblesAug 21, 2025
  An Ariens Lawn Mower engine might run rough due to: * The choke being engaged. Disengage the choke. * A plugged air filter cartridge. Clean or replace the air filter cartridge. * A faulty engine.
J
Jacqueline PughAug 26, 2025
Why Ariens Lawn Mower engine overheats?
- M
  Margaret SmithAug 26, 2025
  Your Ariens Lawn Mower engine may overheat because: * The engine oil level is low. Add engine oil. * The cooling system is plugged. Clean the cooling system. * The engine is faulty.
A
Angela OlsonAug 28, 2025
What to do if Ariens 915163 does not move with engine running when using steering levers?
- J
  Justin FoxAug 29, 2025
  If your Ariens Lawn Mower doesn't move when the engine is running and you're using the steering levers, it could be due to: * The transmission bypass lever being engaged. Disengage the transmission bypass lever. * A faulty hydrostatic belt. Replace the hydrostatic belt. * A faulty transmission.
Y
yjonesSep 1, 2025
What to do if Ariens 915163 does not travel in a straight line?
- C
  Cody BuchananSep 2, 2025
  If your Ariens Lawn Mower isn't traveling in a straight line, consider the following: * Incorrect tire pressure. Check and correct the tire pressure. * Steering levers need adjustment. Adjust the steering levers.
C
cartershawnSep 5, 2025
Why Ariens 915163 Lawn Mower has poor cutting quality?
- M
  Melinda GreenSep 5, 2025
  Poor cutting quality in your Ariens Lawn Mower can stem from: * The mower deck not being level or the mower pitch being incorrect. Level and adjust the pitch of the mower deck. * Dull or faulty mower blades. Sharpen or replace the mower blades.
W
Wendy ReyesSep 9, 2025
What to do if Ariens Lawn Mower hour meter continues when engine not running?
- D
  Daniel JohnsonSep 9, 2025
  If the hour meter on your Ariens Lawn Mower continues to run when the engine is off, it's likely because the ignition key is in the run position. Turn the ignition key to the off position.