Ariens 921031 - Deluxe 24 User Manual

Owner/Operator Manual
Manuel Du Propriétaire/Utilisateur
Models
921013 – Deluxe 30
(SN 075000 +)
921017 – Deluxe 24 Platinum
(SN 075000 +)
921018 – Deluxe 30 Platinum
(SN 075000 +)
921022 – Deluxe 28
(SN 075000 +)
921023 – Deluxe 28 Track
(SN 075000 +)
921027 – Deluxe 28
(SN 000101 +)
921031 – Deluxe 24
(SN 075000 +)
921034 – Deluxe 28
(SN 075000 +)
921 Series
Sno-Thro
®
04335900J 11/12
Printed in USA
E10
The use of any gasoline exceeding 10% ethanol (E10) or
10% MTBE will void the product warranty.
L’utilisation d’une essence contenant plus de 10% d’éthanol
(E10) ou de 10% de MTBE annulent la garantie.
ENGLISH
FRANÇAIS

Ariens 921031 - Deluxe 24 Specifications

General

Engine	Ariens AX 254cc
Clearing Width	24 inches
Speed Settings	6 forward / 2 reverse
Auger Diameter	12 inches
Headlight	Yes
Chute Rotation	200 degrees
Impeller Diameter	12 inches
Tire Size	13 inches
Clearing Depth	21 inches

Summary

Product Delivery and Setup

Delivery Assembly Warning

Improper assembly or adjustments can cause serious injury.

Safety First: Precautions and Alerts

Safety Alerts and Precautions

Understand safety alerts, symbols, and signal words for precautions.

Safe Operating Practices

Follow safe working precautions, stay alert, and learn local laws.

Operator Training Requirements

Ensure proper training for all operators, including yourself.

General Safety Rules

General Safety Rules

Follow all safety practices, be aware of surroundings, and keep children away.

Personal Protective Gear

Wear adequate safety gear including eye protection and gloves.

Assembly Tools and Handlebars

Assembly Tools Required

Gather necessary tools like pliers, wrenches, and screwdrivers before starting.

Discharge Chute Installation

Discharge Chute Crank Installation

Grease chute ring, install chute, connect crank to pinion gear with hairpin.

Chute Control Rod Installation

For 921017/018 models, install chute rod and connect control cable.

Chute Control Mechanisms

Chute Pedestal Hardware Tightening

Tighten pedestal hardware after orienting chute and pedestal vertically.

Chute Control Cable Routing

Route cable correctly and connect to chute rod for proper operation.

Deflector, Skid Shoes, and Interlock

Remote Deflector Control Operation

Connect deflector cable, route it, and check travel for proper adjustment.

Dual Handle Interlock System Check

Verify both clutch levers disengage properly when one is released.

Track, Gearcase, and Engine Checks

Track Tension Check and Adjustment

Check and tension tracks as required for proper unit tracking.

Auger Gearcase Oil Level Check

Check oil level in the auger gearcase as per manual.

Engine Crankcase Oil Level Check

Engine Fuel Tank Filling

Control System Functionality Check

Controls and Features Overview

Key Component Identification

Identify key components like skid shoes, chute crank, and headlights.

Operator Control Identification

Lever and Knob Control Functions

Understand attachment clutch, speed selector, throttle, and choke controls.

Starting and Fuel System Components

Operating the Snow-Thro

Dual Handle Interlock Operation

Traction Drive Clutch Operation

Attachment Clutch Operation

Ignition Switch and Primer Bulb

Speed Selector Operation

Wheel Lock, Skid Shoes, and Fueling

Remote Wheel Lock Operation

Track Angle Adjustment for Snow Clearing

Fuel Tank Filling and Safety

Fill tank with clean, fresh gasoline up to 10% ethanol, in a well-ventilated area.

Pre-Start Inspection Checklist

Frozen Impeller Check Procedure

Clutch Functionality Check

Dual Handle Interlock Check Procedure

Remote Wheel Lock Function Check

Axle Lock Pin Function Check

Starting and Shut Off Procedures

Engine Fuel and Oil Level Check

Check fuel level and engine oil before starting; refer to engine manual.

Emergency Unit Stop Procedure

Release controls immediately to stop in an emergency.

Manual Engine Starting Procedure

Follow steps for manual start including choke, throttle, and recoil starter.

Electric Engine Starting Procedure

Connect extension cord, use starter button; do not operate over 15 sec/min.

Engine and Unit Shutdown

Release clutches, run impeller briefly, then turn ignition key to stop.

Service and Adjustments

Scraper Blade and Skid Shoe Adjustment

Skid Shoes Adjustment for Ground Clearance

Shear Bolts and Adjustment Procedures

Shear Bolt Replacement and Torque

Remote Wheel Lock Cable Adjustment

Remote Deflector Control Adjustment

Clutch and Cable Adjustments

Attachment Cable Slack Removal

Attachment Clutch/Brake Adjustment

Adjust clutch/brake for proper stopping within 5 seconds; prevent injury.

Drive Belt Replacement Procedures

Attachment Drive Belt Replacement

Traction Drive Clutch Adjustment

Adjust traction clutch for friction disc wear; check drive plate finger position.

Friction Disc Replacement Procedure

Friction Disc Replacement Steps

Follow detailed steps to remove and replace the friction disc assembly.

Troubleshooting Common Issues

Troubleshooting Engine Start Issues

Address issues like empty fuel tank, closed valve, or dirty carburetor.

Troubleshooting Engine Stopping Issues

Troubleshoot engine stopping due to fuel, jams, or spark plug issues.

Troubleshooting Drive System Issues

Resolve issues with friction disc, traction belt, or speed selector.

Troubleshooting Snow Throwing Issues

Fix poor snow throwing by checking shear bolts, clutch, or impeller.

Ariens Limited Warranty Information

Warranty Coverage Periods by Use

Understand warranty periods for consumer and commercial use of various products.

Special Warranty Extensions

Warranty Exceptions and Limitations

Items Excluded from Warranty Coverage

Excludes parts not genuine, improper use, wear items, and unauthorized modifications.

Customer Warranty Responsibilities

General Warranty Exclusions

General Warranty Exclusions and Limitations

Lists items not covered, including non-genuine parts, misuse, and normal wear.

Limitation of Remedy and Damages

Evaporative Emission Control Warranty

Owner Responsibilities for Emission Warranty

Evaporative Emission Defect Warranty Requirements