Ariens 924118 - 8524 - User Manual

Questions and Answers

K
Katherine BartonJul 30, 2025
Why won't my Ariens Snow Blower engine crank or start?
- T
  Thomas HarperJul 30, 2025
  If your Ariens Snow Blower engine won't crank or start, possible causes include: the fuel tank is empty (fill it); the fuel shut-off valve is closed (open it); there's a buildup of dirt and residue around the governor/carburetor (clean the area); the key switch is not in the run position (put it in the run position); the ignition switch starter circuit is not functioning (check for a bad starter or connections); or the battery is discharged or wires are loose (check the battery and connections).
W
William SparksAug 6, 2025
Why does my Ariens 924118 - 8524 Snow Blower throw snow poorly?
- C
  colegaryAug 6, 2025
  If your Ariens Snow Blower throws snow poorly or not at all, the issue might be due to broken shear bolts (replace them). Alternatively, the attachment clutch/brake may not be adjusted properly (adjust it), or the attachment drive belt could be worn or damaged (replace it).
C
Craig MolinaAug 14, 2025
What to do if my Ariens 924118 - 8524 Snow Blower engine stops?
- K
  Kristen ShawAug 14, 2025
  If your Ariens Snow Blower engine stops, it could be due to several reasons: * The unit is out of fuel, in which case you should fill the fuel tank. * The fuel shut-off valve is closed; open it. * There's a mechanical jam in the blower rake or impeller. If this happens, turn off the engine, remove the key, wait for all moving parts to stop, check for and remove any obstruction, and then repair before restarting. * The fuel supply is polluted, so replace it with clean fuel. * There's a faulty spark plug; replace or clean it.
B
Brittany PetersAug 21, 2025
Why are there small rubber beads collecting in the frame of my Ariens 924118 - 8524?
- M
  Michael SnyderAug 21, 2025
  The collection of small rubber beads in the frame of your Ariens Snow Blower is typically due to normal friction disc wear. However, if you notice chunks or large pieces of rubber, it indicates that the friction disc should be checked and replaced if necessary.

Summary

CONTROLS AND FEATURES

SAFETY

Safety Alerts

Explains symbols and signal words for safety precautions.

Required Operator Training

Stresses the need for proper training for unit operators.

SAFETY DECALS AND LOCATIONS

Danger! Rotating Parts.

Warns about hazards of rotating parts and proper procedures.

Warning!

Provides crucial warnings for safe operation and interaction.

SAFETY RULES

General Safety Precautions

Outlines essential safety rules for operation and maintenance.

Keep Children and People Away

Advises to keep children and bystanders clear of the work area.

STARTING AND SHUT OFF

Manual Start

Step-by-step instructions for starting the engine using the recoil starter.

Electric Start

Instructions for starting the engine using the electric starter.

ASSEMBLY

OPERATION

Check Function of all Controls

Ensures all unit controls operate correctly before use.

FILLING FUEL TANK

To Add Fuel to Fuel Tank

Detailed steps for safely adding fuel to the tank.

Pre-Start Checks

Essential checks before starting the engine, including frozen impeller.

SNOW REMOVAL

Tips for Operation

Advice on efficient and effective snow removal techniques.

MAINTENANCE SCHEDULE

GENERAL LUBRICATION

SERVICE AND ADJUSTMENTS

TRACTION DRIVE CLUTCH ADJUSTMENT

ATTACHMENT DRIVE BELT REPLACEMENT

TRACTION DRIVE BELT REPLACEMENT

Friction Disc Replacement

TROUBLESHOOTING

Engine Will Not Crank;Start

Lists probable causes and corrections for engine starting issues.

Engine Stops

Lists probable causes and corrections for the engine stopping unexpectedly.

Does Not Operate in Forward; Reverse

Unit Throws Snow Poorly or Does Not Throw Snow

Troubleshooting for poor snow throwing performance.

3-Year Limited Sno-Thro Warranty

Warranty Conditions, Limitations, and Exclusions