Ariens 932035-724 User Manual (English)

Questions and Answers:

P
Paul BrooksJul 31, 2025
Why won't my Ariens 932035-724 Snow Blower engine start?
- J
  Joy PenaJul 31, 2025
  Your Ariens Snow Blower engine might not start due to several reasons: * The fuel tank could be empty, in which case you should fill it. * There might be a buildup of dirt and residue around the governor/carburetor, so clean that area. * The key switch might not be in the run position; ensure it is. * The ignition switch starter circuit might not be functioning, so check for a bad starter or loose connections.
J
Jennifer ColeAug 6, 2025
Why won't my Ariens Snow Blower operate in forward or reverse?
- H
  hunterjorgeAug 6, 2025
  If your Ariens Snow Blower isn't moving forward or reverse, it may be because the friction disc isn't adjusted properly and needs repair or replacement. Alternatively, the traction belt may not be functioning and needs repair or replacement.
J
James LoweAug 12, 2025
What to do if my Ariens Snow Blower engine stops?
- B
  Brittany WilliamsAug 12, 2025
  If your Ariens Snow Blower engine suddenly stops, consider these potential causes: * You might be out of fuel, so refill the fuel tank. * There could be a mechanical jam in the blower rake or impeller. Turn off the engine, remove the key, wait for all moving parts to stop, and then check for and remove any obstructions before restarting. * The fuel supply might be polluted; replace it with clean fuel. * The spark plug could be faulty; try replacing or cleaning it.
M
Michael MorenoAug 18, 2025
What to do if my Ariens 932035-724 Snow Blower unit does not throw snow?
- J
  Joseph FrancisAug 18, 2025
  If your Ariens Snow Blower isn't throwing snow, it could be due to: * Broken shear bolts, which need to be replaced. * Improperly adjusted attachment clutch/brake, requiring adjustment. * A worn or damaged attachment drive belt, which needs replacement.
T
Terrence HarrisAug 25, 2025
Why do small rubber beads collect in the frame of my Ariens Snow Blower?
- J
  Jonathan ChavezAug 25, 2025
  The collection of small rubber beads in the frame of your Ariens Snow Blower is typically due to normal friction disc wear. However, if you notice chunks or large pieces of rubber, the friction disc should be checked and replaced if necessary.

Ariens 932035-724 Specifications

General

Model	932035-724
Engine	Ariens AX
Engine Type	4-Cycle
Engine Displacement (cc)	254
Clearing Width (in)	24
Intake Height (in)	20
Throw Distance (ft)	50
Starting System	Electric Start
Drive Type	Self-Propelled
Number of Speeds	6 Forward / 2 Reverse
Auger Material	Steel
Impeller Diameter	12
Chute Control	Remote
Skid Shoes	Adjustable
Warranty	3 Years
Product Type	Two Stage Snow Blower

Summary

INTRODUCTION TO THE MANUAL

THE MANUAL

General guidance on reading the owner's manual for safe and proper use.

PRODUCT REGISTRATION

Information on completing and returning the warranty registration card.

UNAUTHORIZED REPLACEMENT PARTS

Guidance on using only genuine Ariens replacement parts for safety and performance.

DISCLAIMER OF MANUAL CONTENT

Statement regarding Ariens' right to change products and manual accuracy.

SAFETY GUIDELINES

DELIVERY RESPONSIBILITIES

Customer responsibilities if product is not fully assembled by retailer.

SAFETY ALERTS EXPLANATION

Explanation of safety alert symbols and signal words used in the manual.

OPERATIONAL NOTATIONS

General reference information for proper operation and maintenance practices.

PRACTICES AND LAWS ADHERENCE

Recommendations for safe working practices and adherence to local laws.

REQUIRED OPERATOR TRAINING

Emphasis on proper training for operators and providing the manual.

SAFETY DECALS AND LOCATIONS

DANGER! ROTATING PARTS WARNING

Warning about rotating parts and necessary precautions.

GENERAL WARNINGS AND MANUAL REFERENCE

General warnings about reading the manual and keeping people away.

ASSEMBLY AND OPERATIONAL SAFETY RULES

ASSEMBLY SAFETY RULES

Rules to follow before beginning assembly to avoid injury or damage.

OPERATIONAL SAFETY RULES

Rules for safe operation, including walk-around inspections and work area checks.

OPERATION PROCEDURES

HAZARDOUS SLOPES OPERATION

Precautions for operating the unit on slopes.

UNIT TRANSPORTATION

Guidelines for safely transporting the unit.

UNIT CLEANING

Instructions for cleaning the unit after use.

SPECIFIC OPERATIONAL SAFETY

SPARK ARRESTER REQUIREMENTS

Requirements for engines used on specific land types and maintenance.

FUEL SAFETY RULES

Safety precautions for handling and storing fuel.

MAINTENANCE AND SERVICE SAFETY

Safety rules before performing maintenance or service.

STORAGE SAFETY RULES

Safety precautions for storing the unit, both short and long term.

ACCESSORY AND ATTACHMENT SAFETY

Safety guidelines for using accessories and attachments.

ASSEMBLY INSTRUCTIONS

HANDLEBAR AND SHIFT ROD ASSEMBLY

Instructions for assembling the handlebar and shift rod.

DISCHARGE CHUTE AND CRANK INSTALLATION

Steps for installing the discharge chute and crank.

PRE-START CHECKS AND PROCEDURES

DUAL HANDLE INTERLOCK CHECK

How to check the dual handle interlock function.

TIRE PRESSURE CHECK

How to check and adjust tire pressure.

AUGER GEARCASE OIL CHECK

How to check the oil level in the auger gearcase.

ENGINE CRANKCASE OIL CHECK

How to check the engine crankcase oil level.

FUEL TANK FILLING PROCEDURE

Instructions for safely filling the fuel tank.

CONTROL FUNCTION CHECK

Ensuring all unit controls function properly before operation.

OPERATING THE SNOW THROWER

CONTROLS AND FEATURES OVERVIEW

Identification and function of major controls and features.

DUAL HANDLE INTERLOCK FUNCTION

Explanation of how the dual handle interlock works.

TRACTION DRIVE CLUTCH OPERATION

How to engage and disengage the traction drive clutch.

ATTACHMENT CLUTCH OPERATION

How to engage and disengage the attachment clutch.

SNOW THROWER CONTROLS AND FUELING

CHOKE CONTROL KNOB OPERATION

How to use the choke for starting the engine.

THROTTLE CONTROL OPERATION

How the throttle controls engine speed.

ELECTRIC STARTER USAGE

Instructions for using the electric starter.

RECOIL STARTER HANDLE USE

Proper use of the recoil starter handle.

DISCHARGE CHUTE DEFLECTOR ADJUSTMENT

How to adjust the deflector for snow discharge.

DISCHARGE CHUTE ORIENTATION

How to orient the discharge chute.

CHUTE CRANK FUNCTION

How to use the chute crank for rotation.

AXLE LOCK PIN FUNCTION

Purpose and use of the axle lock pin.

SCRAPER BLADE AND RUNNERS

Information on the scraper blade and runners for ground contact.

FILLING THE FUEL TANK

Detailed steps and safety for refueling the unit.

PRE-START AND STARTING PROCEDURES

FROZEN IMPELLER CHECK

Procedure to check if the impeller is frozen before starting.

CLUTCH FUNCTION CHECK

Verifying proper engagement and disengagement of clutches.

DUAL HANDLE INTERLOCK CHECK

Testing the dual handle interlock mechanism.

AXLE LOCK AND RUNNER ADJUSTMENT

Adjusting axle lock and runners for proper operation.

FUEL AND OIL LEVEL VERIFICATION

Verifying fuel and engine oil levels before starting.

EMERGENCY STOP PROCEDURE

How to stop the unit immediately in an emergency.

ENGINE STARTING AND SHUT OFF

Step-by-step guide for starting and stopping the engine.

OPERATING MODES AND SHUT OFF

ELECTRIC START PROCEDURE

Detailed steps for starting the unit using the electric starter.

ENGINE SHUT OFF PROCEDURE

Steps for safely shutting down the engine and unit.

SNOW REMOVAL OPERATION

Guidelines for effective snow removal.

TRAVELING BETWEEN WORK AREAS

How to move the unit between work areas.

TRANSPORT GUIDELINES

Procedures for safely transporting the unit.

MAINTENANCE SCHEDULE AND CHECKS

MAINTENANCE SCHEDULE

Recommended schedule for performing maintenance tasks.

DUAL HANDLE INTERLOCK CHECK

Verifying the proper function of the dual handle interlock.

FASTENER TIGHTNESS CHECK

Ensuring all hardware is properly tightened.

CLUTCH FUNCTION AND STOPPING CHECK

Verifying clutch engagement and stopping times.

ENGINE AND LUBRICATION MAINTENANCE

ENGINE CLEANING

Instructions for cleaning the engine.

ENGINE OIL CHECKS AND CHANGES

Procedures for checking and changing engine oil.

TIRE PRESSURE MAINTENANCE

Maintaining correct tire pressure.

AUGER GEARCASE LUBRICATION

Checking and maintaining auger gearcase lubricant.

GENERAL LUBRICATION POINTS

Locations and procedures for general lubrication.

AUGER SHAFT LUBRICATION

Specific instructions for lubricating the auger shaft.

SERVICE AND ADJUSTMENTS

DISCHARGE CHUTE DEFLECTOR ADJUSTMENT

Adjusting the deflector for desired drag force.

DISCHARGE CHUTE ORIENTATION AND MESH ADJUSTMENT

Adjusting the chute rotation for proper mesh and tension.

RUNNER, SCRAPER BLADE, AND SHEAR BOLT ADJUSTMENTS

RUNNER ADJUSTMENT

Adjusting runners for proper ground clearance.

SCRAPER BLADE ADJUSTMENT

Adjusting the scraper blade for wear compensation.

SHEAR BOLT REPLACEMENT PROCEDURE

Procedure for replacing shear bolts.

SPEED SELECTOR AND BELT ADJUSTMENTS

SPEED SELECTOR MECHANISM ADJUSTMENT

Steps to adjust the speed selector mechanism.

ATTACHMENT DRIVE BELT REMOVAL

How to remove the attachment drive belt.

ATTACHMENT DRIVE BELT REPLACEMENT

ATTACHMENT DRIVE BELT REPLACEMENT STEPS

Steps for replacing the attachment drive belt.

DRIVE BELT AND CLUTCH ADJUSTMENTS

TRACTION DRIVE BELT REPLACEMENT

Steps for replacing the traction drive belt.

ATTACHMENT CLUTCH/BRAKE ADJUSTMENT

Procedure for adjusting the attachment clutch and brake.

CLUTCH ADJUSTMENT PROCEDURES

TRACTION DRIVE CLUTCH ADJUSTMENT

How to adjust the traction clutch for drive slippage.

FRICTION DISC REPLACEMENT (MODELS 932035, 503)

REMOVING THE FRICTION DISC

Steps to remove the friction disc assembly.

REPLACING THE FRICTION DISC

Steps for installing a new friction disc.

REINSTALLING FRICTION DISC COMPONENTS

Steps for reassembling components after disc replacement.

FRICTION DISC REPLACEMENT (MODELS 932101, 309)

REMOVING THE FRICTION DISC

Steps to remove the friction disc assembly for specific models.

REPLACING THE FRICTION DISC

Steps for installing a new friction disc for specific models.

STORAGE GUIDELINES

SHORT TERM STORAGE

Guidelines for storing the unit for short periods.

LONG TERM STORAGE

Guidelines for storing the unit for extended periods.

TROUBLESHOOTING

ENGINE STARTING ISSUES

Common causes and corrections for engine start issues.

ENGINE STOPPING ISSUES

Causes and corrections for the engine stopping during operation.

DRIVE SYSTEM ISSUES

Causes and corrections for drive system problems.

FRAME DEBRIS ISSUE

Causes and corrections for rubber beads collecting in the frame.

SNOW THROWING PERFORMANCE ISSUES

Causes and corrections for failure to throw snow.

PARTS AND ACCESSORIES

SERVICE PARTS LIST

List of common replacement parts and their part numbers.

AVAILABLE ACCESSORIES LIST

List of available optional accessories for the Sno-Thro.

SPECIFICATIONS

WARRANTY INFORMATION

3 YEAR LIMITED WARRANTY DETAILS

Details of the limited warranty coverage for the Sno-Thro.

WARRANTY CONDITIONS AND EXCLUSIONS

Limitations and exclusions applicable to the warranty.

WARRANTY DISCLAIMER AND LIMITATIONS

Disclaimer of further warranties and limitation of remedies.

Related product manuals

Ariens 932032 - ST724

29 pages

Ariens SNO-THRO 932037 - 724

31 pages

932037 - 724, 932036 - 524, 932504 - 524, 932505 - 724

31 pages

Sno-Thro 932105 - 8526 , 932506 - 8526

30 pages

Ariens 938030-SS21

26 pages

Ariens Sno-Thro 938001

23 pages

Ariens SNO-THRO 938016 - 522

20 pages

Ariens Sno-Thro 939003-ST520E

25 pages

Professional 21 938024-SSR

26 pages

Ariens 920025

34 pages

Ariens 932035-724 User Manual

Table of Contents

Questions and Answers:

Ariens 932035-724 Specifications

Summary

INTRODUCTION TO THE MANUAL

THE MANUAL

PRODUCT REGISTRATION

UNAUTHORIZED REPLACEMENT PARTS

DISCLAIMER OF MANUAL CONTENT

SAFETY GUIDELINES

DELIVERY RESPONSIBILITIES

SAFETY ALERTS EXPLANATION

OPERATIONAL NOTATIONS

PRACTICES AND LAWS ADHERENCE

REQUIRED OPERATOR TRAINING

SAFETY DECALS AND LOCATIONS

DANGER! ROTATING PARTS WARNING

GENERAL WARNINGS AND MANUAL REFERENCE

ASSEMBLY AND OPERATIONAL SAFETY RULES

ASSEMBLY SAFETY RULES

OPERATIONAL SAFETY RULES

OPERATION PROCEDURES

HAZARDOUS SLOPES OPERATION

UNIT TRANSPORTATION

UNIT CLEANING

SPECIFIC OPERATIONAL SAFETY

SPARK ARRESTER REQUIREMENTS

FUEL SAFETY RULES

MAINTENANCE AND SERVICE SAFETY

STORAGE SAFETY RULES

ACCESSORY AND ATTACHMENT SAFETY

ASSEMBLY INSTRUCTIONS

HANDLEBAR AND SHIFT ROD ASSEMBLY

DISCHARGE CHUTE AND CRANK INSTALLATION

PRE-START CHECKS AND PROCEDURES

DUAL HANDLE INTERLOCK CHECK

TIRE PRESSURE CHECK

AUGER GEARCASE OIL CHECK

ENGINE CRANKCASE OIL CHECK

FUEL TANK FILLING PROCEDURE

CONTROL FUNCTION CHECK

OPERATING THE SNOW THROWER

CONTROLS AND FEATURES OVERVIEW

DUAL HANDLE INTERLOCK FUNCTION

TRACTION DRIVE CLUTCH OPERATION

ATTACHMENT CLUTCH OPERATION

SNOW THROWER CONTROLS AND FUELING

CHOKE CONTROL KNOB OPERATION

THROTTLE CONTROL OPERATION

ELECTRIC STARTER USAGE

RECOIL STARTER HANDLE USE

DISCHARGE CHUTE DEFLECTOR ADJUSTMENT

DISCHARGE CHUTE ORIENTATION

CHUTE CRANK FUNCTION

AXLE LOCK PIN FUNCTION

SCRAPER BLADE AND RUNNERS

FILLING THE FUEL TANK

PRE-START AND STARTING PROCEDURES

FROZEN IMPELLER CHECK

CLUTCH FUNCTION CHECK

DUAL HANDLE INTERLOCK CHECK

AXLE LOCK AND RUNNER ADJUSTMENT

FUEL AND OIL LEVEL VERIFICATION

EMERGENCY STOP PROCEDURE

ENGINE STARTING AND SHUT OFF

OPERATING MODES AND SHUT OFF

ELECTRIC START PROCEDURE

ENGINE SHUT OFF PROCEDURE

SNOW REMOVAL OPERATION

TRAVELING BETWEEN WORK AREAS

TRANSPORT GUIDELINES

MAINTENANCE SCHEDULE AND CHECKS

MAINTENANCE SCHEDULE

DUAL HANDLE INTERLOCK CHECK

FASTENER TIGHTNESS CHECK

CLUTCH FUNCTION AND STOPPING CHECK

ENGINE AND LUBRICATION MAINTENANCE

ENGINE CLEANING

ENGINE OIL CHECKS AND CHANGES