Ariens 932101-824 User Manual (English)

Questions and Answers:

A
Amber MarquezAug 8, 2025
Why won't my Ariens 932101-824 engine start?
- B
  Brandon KnoxAug 8, 2025
  Your Ariens Snow Blower engine might not start due to several reasons: * The fuel tank could be empty, in which case you should fill it. * There might be a buildup of dirt and residue around the governor/carburetor, so clean that area. * The key switch might not be in the run position; ensure it is. * The ignition switch starter circuit might not be functioning, so check for a bad starter or loose connections.
C
charles29Aug 14, 2025
Why won't my Ariens 932101-824 Snow Blower operate in forward or reverse?
- G
  ggarciaAug 14, 2025
  If your Ariens Snow Blower isn't moving forward or reverse, it may be because the friction disc isn't adjusted properly and needs repair or replacement. Alternatively, the traction belt may not be functioning and needs repair or replacement.
N
Nicholas MendozaAug 20, 2025
What to do if my Ariens 932101-824 engine stops?
- K
  Kylie SmithAug 20, 2025
  If your Ariens Snow Blower engine suddenly stops, consider these potential causes: * You might be out of fuel, so refill the fuel tank. * There could be a mechanical jam in the blower rake or impeller. Turn off the engine, remove the key, wait for all moving parts to stop, and then check for and remove any obstructions before restarting. * The fuel supply might be polluted; replace it with clean fuel. * The spark plug could be faulty; try replacing or cleaning it.
G
Gerald RossAug 26, 2025
What to do if my Ariens Snow Blower unit does not throw snow?
- B
  Brian ShafferAug 26, 2025
  If your Ariens Snow Blower isn't throwing snow, it could be due to: * Broken shear bolts, which need to be replaced. * Improperly adjusted attachment clutch/brake, requiring adjustment. * A worn or damaged attachment drive belt, which needs replacement.
A
alexandria23Aug 31, 2025
Why do small rubber beads collect in the frame of my Ariens 932101-824 Snow Blower?
- D
  danielhowellAug 31, 2025
  The collection of small rubber beads in the frame of your Ariens Snow Blower is typically due to normal friction disc wear. However, if you notice chunks or large pieces of rubber, the friction disc should be checked and replaced if necessary.

Ariens 932101-824 Specifications

General

Engine Type	4-cycle
Speed Settings	6 forward / 2 reverse
Forward Speeds	6
Reverse Speeds	2
Auger Type	Serrated steel
Auger Material	Steel
Type	Two-stage
Impeller Diameter	12 inches
Electric Start	Yes
Clearing Width	24 in
Intake Height	20 inches
Warranty	3 years limited
Starting System	Electric start
Chute Control	Manual

Summary

Model Compliance Information

Manufacturer's Declaration of Conformity

Formal declaration by Ariens Company regarding product compliance with EC directives and standards.

Sound Level Specifications

Measured vs. Guaranteed Sound Power

Comparison of representative measured and guaranteed sound power levels for different models.

Controls and Features Overview

Component Identification

Lists and identifies key controls and features of the snow thrower with corresponding numbers.

Manual Introduction and Guidelines

Product Registration and Warranty

Information on completing the warranty registration card to activate product warranty.

Unauthorized Replacement Parts Policy

Ariens' policy on using only genuine parts to maintain performance, durability, and safety.

Company Disclaimer

Ariens reserves the right to change products without notice; manual details were current at printing.

Essential Safety Information

Safety Alerts and Notations

Explains safety alert symbols, signal words, and important notes for safe operation and unit protection.

Safe Operating Practices and Laws

Guidelines for safe working practices, adherence to laws, and awareness of potential hazards.

Operator Training Requirements

Emphasizes the need for proper training for original and subsequent operators of the unit.

Safety Decals and Locations

Decal Identification and Placement

Illustrates locations of DANGER, WARNING, and safety decals with explanations of their messages.

Critical Safety Warnings and Rules

Specific Danger and Hot Surface Warnings

Highlights critical danger warnings for rotating parts and hot surfaces, advising caution.

Assembly and Operational Safety Rules

Rules for safe assembly, pre-operation checks, and general operational safety practices.

Operational Guidelines and Precautions

Safe Operation on Slopes and Transport

Instructions for safe operation on slopes, unit transport, and cleaning procedures.

Safety Rules for Fuel, Maintenance, and Storage

Fuel Safety and Handling Rules

Critical safety guidelines for handling fuel, refueling, and preventing spills.

Maintenance, Storage, and Accessory Safety

Safety rules for performing maintenance, storing the unit, and using accessories.

Snow Thrower Assembly Instructions

Handlebar and Shift Rod Assembly

Step-by-step guide to assemble the handlebar and connect the shift rod.

Discharge Chute Installation

Instructions for installing the discharge chute and its crank mechanism.

Pre-Operation Checks and Fluid Levels

System Function Checks

Procedures to check dual handle interlock, tire pressure, and engine/gearcase oil levels.

Fueling and Control Verification

Steps for filling the fuel tank and verifying all unit controls are functioning correctly.

Snow Thrower Operation Procedures

Starting and Engagement Controls

Explanation of attachment belt break-in, dual handle interlock, and operation of traction/attachment clutches.

Ignition, Primer, and Speed Selector

Details on using the ignition switch, primer bulb, and speed selector for unit control.

Detailed Operational Controls

Choke, Throttle, and Starting Mechanisms

Instructions for using the choke, throttle, electric starter, and recoil starter handle.

Chute, Blade, and Fueling Procedures

Guides for adjusting chute, scraper blade, runners, and filling the fuel tank.

Pre-Start Checks and Engine Starting

Pre-Start Inspections

Checks for frozen impeller, clutch function, dual handle interlock, and fluid levels before starting.

Engine Starting Procedure

Step-by-step guide for manual engine start, including priming, choke, and throttle settings.

Starting, Shutting Off, and Snow Removal

Electric Start and Engine Shut-Off

Instructions for electric starting, safe engine shut-off, and snow removal techniques.

Traveling and Transporting the Unit

Guidelines for moving the unit between areas and safely transporting it.

Scheduled Maintenance Tasks

Maintenance Schedule Overview

A chart detailing recommended maintenance tasks and their frequency based on usage hours.

Clutch and Fastener Checks

Procedures for checking dual handle interlock, fasteners, and clutch engagement/disengagement.

Engine and Lubrication Maintenance

Engine Cleaning and Oil Management

Instructions for cleaning the engine, checking, and changing engine oil.

Tire Pressure, Gearcase, and General Lubrication

Guidance on checking tire pressure, auger gearcase oil, and general unit lubrication points.

Service and Adjustments

Discharge Chute and Deflector Adjustment

Instructions for adjusting the discharge chute and deflector for proper snow direction.

Runner, Blade, and Shear Bolt Adjustments

Runner, Scraper Blade, and Shear Bolt Procedures

Guides for adjusting runners, scraper blade, and replacing shear bolts.

Drive System Adjustments and Belt Replacement

Speed Selector and Attachment Belt Replacement

Procedures for adjusting the speed selector and replacing the attachment drive belt.

Drive Belt Adjustment and Clutch Calibration

Traction Belt and Clutch/Brake Adjustment

Instructions for adjusting traction drive belt and attachment clutch/brake mechanisms.

Clutch Adjustment Details

Traction Drive Clutch Adjustment

Steps to adjust the traction drive clutch to compensate for friction disc wear.

Friction Disc Replacement (Models 932035, 503)

Disc Removal and Installation Procedure

Detailed steps for removing and replacing the friction disc on specific snow thrower models.

Friction Disc Replacement (Models 932101, 309)

Disc Replacement Steps

Instructions for removing and installing the friction disc for specific snow thrower models.

Storage and Troubleshooting Guide

Short-Term and Long-Term Storage

Guidelines for storing the snow thrower for short and extended periods, including cleaning and fuel removal.

Common Problem Diagnosis

Identifies common engine and drive problems with their probable causes and corrective actions.

Service Parts and Accessories

Replacement Parts and Optional Accessories

Lists part numbers for common replacement parts and available accessories for the snow thrower.

Technical Specifications

Model and Performance Data

Detailed specifications including model numbers, engine details, dimensions, weight, and sound/vibration levels.

Warranty Information

Limited Warranty Terms and Conditions

Outlines the 3-year limited warranty, its coverage, conditions, limitations, and exclusions.

Related product manuals

Sno-Thro 932105 - 8526 , 932506 - 8526

30 pages

Ariens 932035-724

32 pages

Ariens 932032 - ST724

29 pages

Ariens SNO-THRO 932037 - 724

31 pages

932037 - 724, 932036 - 524, 932504 - 524, 932505 - 724