Ariens Platinum SHO 28 RapidTrak User Manual (English)

Questions and Answers:

D
David ArroyoAug 19, 2025
Why does my Ariens Platinum SHO 28 RapidTrak Snow Blower engine start hard or run poorly?
- R
  Ryan ThomasAug 19, 2025
  If your Ariens snow blower engine starts hard or runs poorly, it could be due to a faulty, fouled, or incorrectly gapped spark plug (clean and correctly set the spark plug gap). Another reason could be that the fuel mixture is too rich (turn the choke control knob to the off position). Additionally, a blocked fuel cap vent (install a new fuel cap) or a contaminated fuel supply (replace with clean fuel) could be the cause.
C
chapmanmaryAug 21, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak Snow Blower unit does not throw snow or throws it poorly?
- R
  Robert CharlesAug 22, 2025
  If your Ariens snow blower isn't throwing snow effectively, start by checking the shear bolts. Next, inspect the impeller for ice; if frozen, move the unit to a warm place to thaw. Also, check the auger for obstructions. Stop the engine, remove the key, and wait for moving parts to stop before removing any obstructions. Clear any snow clogging the discharge chute, remember to stop the engine, remove the key, wait for all moving parts to stop and for hot parts to cool, and use a clean-out tool, not your hands. A slipping, worn, or damaged auger drive belt may also be the cause.
C
Caroline LopezAug 25, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak unit runs briefly then stops?
- M
  Madison FernandezAug 26, 2025
  If your Ariens snow blower unit runs briefly then stops, it may be due to a build-up of fumes in the fuel tank creating too much pressure. Try slowly loosening the fuel tank cap.
J
johnssamanthaAug 28, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak Snow Blower unit does not drive forward or in reverse?
- L
  loriburkeAug 28, 2025
  If your Ariens snow blower does not drive forward or in reverse, the friction disc may be worn (replace the friction disc). Also, the traction drive cable might not be adjusted correctly (remove slack from the cable). Another reason could be that the traction belt is not functioning (repair or replace the traction drive belt). Finally, the speed selector might not be adjusted correctly (adjust the speed selector).
T
timothy43Aug 30, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak Snow Blower engine stops?
- D
  Devon IrwinAug 30, 2025
  If your Ariens snow blower engine stops, it could be due to several reasons. Check if the fuel tank is empty and fill it if necessary. Ensure the fuel valve is open. Look for any obstructions in the auger or impeller; if there are any, stop the engine, remove the key, wait for all moving parts to stop, and then remove the obstruction before restarting. Also, check for a contaminated fuel supply and replace it with clean fuel if needed. Other potential causes include a faulty engine (consult your Ariens dealer or authorized engine manufacturer’s service center), a faulty spark plug (replace or clean it), or a blocked fuel cap vent (install a new fuel cap).
P
Paul WilliamsSep 2, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak Snow Blower belt squeals continuously?
- L
  Lori HughesSep 3, 2025
  If your Ariens snow blower belt squeals continuously, the impeller may be frozen (move the unit to a warm area to thaw). Another cause could be that the attachment clutch needs adjustment.
B
browncynthiaSep 6, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak unit pulls to the left or right?
- P
  Peter NelsonSep 6, 2025
  If your Ariens snow blower unit pulls to the left or right, the skid shoes and scraper blade may need adjustment. Adjust the skid shoes and scraper blade.
R
rodriguezloriSep 9, 2025
What to do if my Ariens Platinum SHO 28 RapidTrak leaves excessive snow behind?
- Y
  ybellSep 9, 2025
  If your Ariens snow blower is leaving excessive snow behind, the scraper blade may be worn or damaged. Adjust the scraper blade when worn, and replace it when damaged or when it has been adjusted down as far as possible and does not touch the ground or clear correctly.
P
Paul MitchellSep 12, 2025
Why are there small rubber beads collecting in the frame of my Ariens Platinum SHO 28 RapidTrak Snow Blower?
- M
  Margaret ClarkSep 12, 2025
  The presence of small rubber beads collecting in the frame of your Ariens snow blower is normal friction disc wear. No correction is needed unless there are chunks or large pieces of rubber collecting in the frame.