Ariens ST 928 LE User Manual

General information about the manual's purpose, usage, and directional references.

Information on ordering parts and identifying unit serial numbers for service inquiries.

Information on activating the warranty via the product registration card.

Warning against using non-Ariens parts and liability disclaimers for performance and safety.

Ariens' right to alter products; manual's specifications are in effect at printing.

Types of communications dealers receive for product updates, issues, and safety campaigns.

Explains safety symbols, and the meanings of DANGER, WARNING, and CAUTION signal words.

Covers NOTE/IMPORTANT usage and general safe working practices and applicable laws.

Emphasizes the importance of operator training and work area preparation for safety.

Details proper unit positioning for service and guidelines for cleaning and storage.

General rules for operation, slopes, child safety, personal safety, and controls.

Technical specifications for Ariens Snow-Thro models 924080 through 924084.

Technical specifications for Ariens Snow-Thro models 924085 through 924089.

Technical specifications for Ariens Snow-Thro models 924090 through 924100.

Technical specifications for Ariens Snow-Thro models 924101 through 924105.

Technical specifications for Ariens Snow-Thro models 924106 through 924314.

Technical specifications for Ariens Snow-Thro models 924315 through 924319.

Technical specifications for Ariens Snow-Thro models 924320 through 924325.

Technical specifications for Ariens Snow-Thro models 924326 through 92410700.

Identifies and illustrates major controls and components of the snow-thro with diagrams.

Procedures for placing the unit in belt and on-end service positions for maintenance.

Safe procedures and warnings for refueling the unit's fuel tank.

Information on the importance and correct usage of the fuel shut-off valve.

Details lubrication points, types of grease, and recommended frequency.

Instructions on how to check and maintain lubricant levels in the auger gearcase.

Covers engine cooling requirements and daily oil level checks and changes.

Step-by-step guide for safely replacing the traction drive belt.

Step-by-step guide for safely replacing the attachment drive belt.

Details on using Ariens shear bolts for auger protection against jamming.

Recommended tire pressure for optimal unit performance and safety.

Procedures for adjusting the discharge chute, runners, and scraper blade.

Procedure for adjusting the chute crank for smooth rotation.

How to properly adjust the attachment clutch and impeller brake.

Procedure to adjust the traction drive clutch to compensate for wear and slippage.

Steps to adjust the speed selector linkage for proper gear changes.

Instructions for removing drive chain links and adjusting drive chain tension.

Removal and reassembly of the upper handlebar panel and ignition switch.

Steps to remove and install the lower handlebar from the frame.

Procedure for removing and servicing the attachment clutch handle.

How to adjust the attachment clutch for proper engagement and disengagement.

Procedure for removal and replacement of the wheel drive clutch lever and traction rod.

Procedures for removing and servicing clutch yoke and fork components.

Chart for identifying and resolving common engine operational problems with causes and actions.

Step-by-step instructions for safely removing the engine from the unit.

Step-by-step instructions for safely installing the engine onto the unit.

Procedures for removing and servicing the differential, lockout, and axle components.

How to remove and service the axle bearings.

Procedures for removing and servicing the pinion, shaft, and sprocket.

Instructions for removing and servicing the reduction shaft.

Procedures for servicing the hex shaft and its associated bearings.

Steps for removing drive chain links and adjusting drive chain tension.

Detailed steps for replacing the friction wheel.

Procedures for removing and servicing the friction wheel carrier.

Step-by-step guide to removing the auger and impeller assembly.

How to adjust the scraper blade to compensate for wear.

Instructions for replacing shear bolts that protect the auger drive.

Steps for removing and securing the discharge chute.

Guide for installing a new deflector cable and adjusting the deflector.

How to adjust runners for different snow and surface conditions.

Procedures for removing and servicing the cast iron gear case, including lubrication.

Procedures for removing and servicing the aluminum gear case, including bushings and lubrication.