29
commissioningmessa in funzione
Tabella riepilogativa gas
FAST EVO ONT C 11 FAST EVO ONT C 14
G20 G230 G30 G31 G20 G230 G30 G31
Indice di Wobbe inferiore
Lower Wobbe index
(15°C, 1013 mbar)
MJ/m
3
45,67 38,9 80,58 70,69 45,67 38,9 80,58 70,69
Pressione nominale di alimentazione
Gas inlet pressure
mbar 20 20 28/30 37 20 20 28/30 37
Pressione massima al bruciatore
Gas Burner Pressure max
mbar 15,0 10,35 24,3 32,3 14,0 9,8 26,4 34,7
Pressione minima al bruciatore
Gas Burner Pressure min
mbar 3,0 2,16 4,5 6,7 2,2 1,6 3,5 5,0
Pressione di lenta accensione
Slow ignition pressure
mbar 4,0 3,4 5,5 8,3 2,71 2,0 4,1 6,0
parametro PA - Impostazione modello e gas
utilizzato
PA Parameter - Setting model and type of gas
PA 01 04 02 03 08 11 09 10
Ugelli bruciatore
Main Burner jets
nr. 11 13
Ø ugelli bruciatore principale
Ø burner jets
mm 1,15 1,3 0,75 0,75 1,2 1,35 0,8 0,8
Consumi
Consumption
(15°C, 1013 mbar) (G.N.= m
3
/h) (LPG kg/h))
massimo
max
2,28 1,76 1,70 1,67 2,86 2,22 2,13 2,10
FAST EVO ONT C 16
G20 G230 G30 G31
Indice di Wobbe inferiore
Lower Wobbe index
(15°C, 1013 mbar)
MJ/m
3
45,67 38,9 80,58 70,69
Pressione nominale di alimentazione
Gas inlet pressure
mbar 20 20 28/30 37
Pressione massima al bruciatore
Gas Burner Pressure max
mbar 11,1 10,6 21,21 28,5
Pressione minima al bruciatore
Gas Burner Pressure min
mbar 1,4 1,4 2,42 3,0
Pressione di lenta accensione
Slow ignition pressure
mbar 1,9 1,7 2,7 3,6
parametro PA - Impostazione modello e gas
utilizzato
PA Parameter - Setting model and type of gas
PA 15 18 16 17
Ugelli bruciatore
Main Burner jets
nr. 14
Ø ugelli bruciatore principale
Ø burner jets
mm 1,3 1,35 0,8 0,8
Consumi
Consumption
(15°C, 1013 mbar)(G.N.= m
3
/h) (LPG kg/h))
massimo
max
3,28 2,54 2,45 2,41
Cambio Gas
L’apparecchio può essere trasformato per uso da gas
metano (G20) a Gas Liquido (G30-G31) o viceversa a
cura di un Tecnico Qualifi cato con l’utilizzo dell’apposito
Kit.
Gas Changeover
The appliance may be adjusted so that it may be used
with Liquid Gas (G30-G31) instead of methane gas
(G20) or vice-versa. The adjustment must be performed
by a Qualifi ed Technician using the special Kit.
Gas setting table