To Next PageTo Next PageWhat to do if the Arizona Instrument Measuring Instruments says 'Data Memory Full'?
If your Arizona Instrument Measuring Instruments displays 'Data Memory Full', you should save your current data and then proceed to delete the existing data. Consult 'Retrieving Data on page 29' for detailed instructions.
What to do if Arizona Instrument JEROME J605 shows 'Incomplete Regen – Check battery/AC power supply'?
If your Arizona Instrument Measuring Instruments displays 'Incomplete Regen – Check battery/AC power supply', it means the external power was interrupted during regeneration. Reconnect the external power, let the sensor cool down, and then restart the regeneration process.
What does 'Regen High Temp Error' mean on Arizona Instrument Measuring Instruments?
If your Arizona Instrument Measuring Instruments shows 'Regen High Temp Error. Incomplete Regen.', it indicates that the sensor temperature was too high during regeneration. Allow the sensor to cool down before restarting the regeneration process.
Why Arizona Instrument JEROME J605 requires sensor regeneration?
If your Arizona Instrument Measuring Instruments requires sensor regeneration, it is because the sensor is saturated with hydrogen sulfide. Perform a sensor regeneration, as described on page 23.
What to do if airflow is restricted in Arizona Instrument JEROME J605?
If your Arizona Instrument Measuring Instruments shows restricted airflow during the sensor regeneration cycle, periodically check the Tygon® tubing (refer to page 34). Ensure that the ports are not obstructed. Also, change the intake fritware filter (refer to page 33).
Why Arizona Instrument JEROME J605 Measuring Instruments giving high or erratic results?
If your Arizona Instrument Measuring Instruments provides high or erratic results, and you are sampling in a dusty area, the intake and internal filters may be clogged and require replacement. Open the instrument and check for pinched, crimped, or disconnected internal tubing. In extreme conditions, you might need to install an additional particle filter on the intake.
How to troubleshoot high erratic results on Arizona Instrument Measuring Instruments?
If your Arizona Instrument Measuring Instruments provides high erratic results, install the Zero Air Filter in the intake and press the SAMPLE button. If readings exceed 3 ppb after three samples at 15-second intervals, replace the fritware filter and Tygon® tubing (refer to page 33). Perform sensor regeneration with the Zero Air Filter in the intake (refer to page 23). If needed, retest, and replace the scrubber filters and Tygon® tubing (refer to page 34). This is due to internal hydrogen sulfide contamination.
What to do if Arizona Instrument Measuring Instruments USB Printer is not responding?
If your Arizona Instrument Measuring Instruments is not responding or not connected to a USB printer, turn the printer off and then back on. Also, ensure that the printer is correctly connected to the J605 port and is online.
Why Arizona Instrument JEROME J605 does not turn on with AC power?
If your Arizona Instrument Measuring Instruments is not turning on when connected to AC power, the fuse might be open, there might be insufficient power, or there could be an internal component failure. Wait for the fuse to reset automatically. Use a voltmeter to check the AC outlet for power. For further assistance, contact AZI Customer Service at 800-528-7411 or 602-470-1414.
Why is my Arizona Instrument Measuring Instruments giving false readings?
If your Arizona Instrument Measuring Instruments gives false readings, it might be due to extremely cold or warm air being sampled. Run the Warm-up function as described in the REGEN menu. Alternatively, when sampling under such conditions, install the Zero Air Filter in the intake and sample every 15 seconds until the display reads 3 ppb or less to equilibrate the sensor temperature. Then, remove the filter and continue sampling.
General| Brand | Arizona Instrument |
|---|---|
| Model | JEROME J605 |
| Category | Measuring Instruments |
| Language | English |
Turn on the instrument and check display for serial number and software revision.
The instrument is not designed for explosive environments.
Press the SAMPLE button to initiate a sampling cycle for H2S measurement.
Perform sensor regeneration at the beginning of each day for optimal performance.
Caution that the instrument is for gaseous vapor use only and not liquids or dust.
Details and explains all elements displayed on the J605 main screen.
Start the sensor regeneration process to clean the sensor.
Set high and low alarm thresholds for hydrogen sulfide concentration.
Crucial warning to prevent sensor damage by not leaving H2S on the sensor overnight.
Explains the 4-20mA analog output for industrial systems and its scaling.
Use of the Functional Test Module to verify instrument operation between calibrations.
Solutions for issues like the instrument not turning on or the battery not holding a charge.
Solutions for airflow restrictions, erratic results, and contamination.
Step-by-step guide to install the necessary USB driver for PC connectivity.
