Armacost Lighting RibbonFlex PRO 451200 - User Manual

SAFETY INFORMATION
■
DANGER: Risk of eye damage. Do not stare directly at the LED chips
of this LED strip.
■
CAUTION: Do not power LED tape while coiled on reel.
■
IMPORTANT: Always observe polarity for 12-volt connections, positive
(+) to positive and negative (–) to negative.
■
IMPORTANT: Do not install Class 2 low voltage wiring in the same runs
as AC main power. If AC and low voltage wires cross, keep them at
90-degree angles. Use only insulated staples, plastic ties, or wire
support clips to secure cords and wires.
■
NOTICE: LED fl exible tape lighting rating: 12VDC 3A.
■
Only use the 12-volt LED lighting power supply which has been
provided with this kit.
■
Do not bend, crush or pull the cable. Protect from sharp edges,
oil and heat.
■
For indoor/dry location use only.
■
Ensure the connectors are securely fastened before operating the tape.
■
Electrical waste should not be disposed of with household waste.
Please recycle where facilities exist.
Three-year limited warranty
WHAT IS COVERED
The manufacturer warrants this fi xture to be free from defects in materials
and workmanship for a period of three (3) years from date of purchase.
This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is
the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifi cations, alteration, neglect, or mishandling. This warranty
shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration,
faulty installation, or any other failure not relating to faulty material or
workmanship. This warranty shall not apply to the fi nish on any portion of
the product, such as surface and/or weathering, as this is considered normal
wear and tear.
WHAT IS NOT COVERED
The manufacturer does not warrant and specifi cally disclaims any warranty,
whether expressed or implied, of fi tness for a particular purpose, other than
the warranty contained herein. The manufacturer specifi cally disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/ expense costs involved in
the replacement or repair of said product.
Contact customer support at 410-354-6000, support@armacostlighting.com,
or visit armacostlighting.com/support.
Installation considerations
■
Where will you locate your power supply?
■
How will you run and conceal the wires to your LED tape lighting?
■
What is the best mounting position for the LED tape light to achieve
your desired effect?
■
See the section titled “Mounting options” for cabinet lighting
placement tips.
PACKAGE CONTENTS
Plug-in power supply
RF receiver and 8.2 feet
LED tape light (pre-assembled)
RF dimmer
remote
SureLock Wire Lead Connectors (optional use)
Wire support clips
INSTALLATION
Cutting the tape light or extending the tape
light length (optional)
■
Using the provided connectors, this tape light system can be
extended to a total length of up to 5m
■
Use only Armacost RibbonFlex Pro item #142210 (sold separately)
to extend the tape length
■
Additional connectors are available through the point-of-purchase
or directly from armacostlighting.com
■
IMPORTANT: Make sure to observe polarity when making connections,
positive to positive and negative to negative. Check to see that the
wire colors and the polarity markings printed on the tape line up.
Positive
Negative
■
To use the included SureLock Connectors, cut the LED tape with
scissors in the center of a copper pad (position A) as shown, or attach
the connector to the copper pad found at the end of the tape.
■
The tape can also be cut at silver solder joints (position B), but this
cut point should be used for soldered connections only.
Cut tape at
center of
copper pads
B
Okay to cut at solder
joints, but do not
use connector
A
■
Use a SureLock Connector to make turns and go around corners. They
can also be spliced and extended for gaps of any size. 18–20 AWG
wire is recommended for custom lengths (not included).
(
+
)
(
–
)
length to
fi t needs
(
–
)
(
+
)
(
–
)
(
+
) (
+
)
(
–
)
NOTE: Be sure all 12-volt connections are secure and protected from
electrical shorting. Options include electrical tape, small wire nuts, crimp
connectors, etc.
1
LED Tape Light Kit
Item
451200

Summary

Safety Information

General Safety Precautions

Follow safety guidelines for eye protection, coiled tape, polarity, wire routing, and proper power supply usage.

Three-Year Limited Warranty

Warranty Coverage

Covers defects in materials and workmanship for three years from purchase date for original consumer.

Exclusions from Warranty

Disclaims fitness for particular purpose, excludes consequential/incidental loss, labor costs, and misuse.

Installation Guide

Package Contents

Lists components included in the LED tape light kit: power supply, RF receiver, remote, and connectors.

Cutting and Extending Tape Light

Details how to cut the LED tape light at designated points and extend length using specific connectors.

Using SureLock Connectors

Step-by-step guide on how to open, insert LED strip, and secure SureLock connectors for joining tape sections.

Soldering LED Tape

Explains soldering as an alternative method for joining wires and tape light sections.

Preparing Assembly Location

Instructions on how to temporarily position the LED tape lighting before final mounting.

Installing Power Supply

Guidance on connecting the AC power cord to an outlet and ensuring proper operation.

Direct Wiring Power Supply

Procedure for direct wiring the power supply to a branch circuit, with safety warnings.

Above Cabinet Uplighting

Techniques for creating indirect uplighting over cabinets using LED tape light strips.

Mounting Options

Provides tips for surface mounting, positioning for optimal light, and reducing reflections.

Operation and Troubleshooting

Remote Control Functions

Explains how to use the remote for turning lights on/off, adjusting brightness, and selecting dynamic effects.

Pairing Multiple Kits

Instructions for pairing multiple LED tape light kits to a single remote control.

Changing Remote Battery

Procedure for replacing the CR2025 button battery in the remote control.

Troubleshooting LED Strip Issues

Addresses common problems like the LED strip not lighting or only parts lighting up.

FCC Compliance Statement

Details FCC rules, conditions for operation, and measures to correct interference.

Overview

1. Function Description
2. Usage Features
3. Maintenance Features

The Armacost RibbonFlex PRO LED Tape Light Kit (Item 451200) is a versatile lighting solution designed for indoor/dry locations, offering customizable illumination for various applications, particularly under cabinets and for uplighting. This kit includes an RF receiver, an 8.2-foot LED tape light (pre-assembled), a plug-in power supply, an RF dimmer remote, SureLock Wire Lead Connectors (optional use), and wire support clips.

Function Description:

The core function of this device is to provide flexible, low-voltage LED lighting. The LED tape light can be cut to specific lengths or extended using additional connectors and tape, allowing for tailored installations. It operates on a 12VDC 3A power supply, ensuring safe and efficient operation. The included RF dimmer remote enables users to control the lighting wirelessly, adjusting brightness, turning the lights ON/OFF, and selecting from various dynamic fade and strobe effects. The remote's RF technology means it does not require line-of-sight to operate the lights, offering convenience in placement. The system is designed for easy installation, with an adhesive backing on the LED tape for surface mounting and SureLock Connectors for making turns, going around corners, or splicing to extend lengths.

Usage Features:

• Customizable Length: The LED tape light can be cut with scissors at designated copper pads or silver solder joints to achieve the desired length. It can also be extended up to a total length of 5 meters using Armacost RibbonFlex Pro item #142210 (sold separately) or additional SureLock Connectors.
• Flexible Installation: The tape light's flexibility allows it to be installed in curved and irregular spaces. The adhesive backing facilitates surface mounting, while SureLock Connectors simplify turns and extensions.
• Wireless Control: The RF dimmer remote provides comprehensive control over the lighting. Users can:
  • Turn lights ON or OFF.
  • Adjust brightness incrementally or use quick access buttons for preset levels (100%, 50%, 25%, 10%).
  • Select from various fade and strobe dynamic effects.
  • Increase or decrease the speed of the selected dynamic effect.
  • The remote operates without line-of-sight, with a range of up to 50 feet in optimal conditions.
• Mounting Options:
  • Under Cabinet Lighting: For continuous runs under cabinets, a 1/2-inch hole may be drilled through cabinet side lips. To maximize light output and focus on the work surface, mount the tape 1-2 inches behind the front cabinet lip, which works best with dull or matte finished countertops. To reduce bright spots on highly reflective countertops, mount the tape light on the inside back of the cabinet lip frame facing the backsplash. For cabinets or shelves without a lip, a visual barrier (e.g., quarter round molding) can be used to hide the LEDs.
  • Above Cabinet Uplighting: For indirect uplighting, mount the LED tape on a rigid strip (e.g., thin lattice or corner guard molding) on top of cabinets. Angle the strip to achieve desired illumination. To create a seamless glow and avoid bright spots, position the tape light strip farther from adjacent walls.
• Polarity Observation: It is crucial to observe polarity (+ to + and - to -) when making all 12-volt connections to ensure proper operation and prevent electrical shorting. Wire colors and polarity markings on the tape should align.
• Multi-Kit Pairing: Multiple kits can be paired to a single remote for synchronized control. The pairing process involves unplugging the power supply, waiting 5 seconds, restoring power, and then pressing and holding the 50% and 10% buttons on the remote within 10 seconds. Kits can also be returned to single-remote operation using a unique remote.
• Soldering Option: For more permanent or custom connections, wires can be soldered directly to the tape light or sections of tape light can be soldered together.

Maintenance Features:

• Cleaning: The light can be cleaned with a clean, dry, or slightly damp cloth. Avoid using cleaners with chemicals, solvents, or harsh abrasives, as these can damage the light strip.
• Battery Replacement: The remote uses a CR2025 DC 3V button battery. To replace, push in the tab on the side of the battery tray and pull it out. Always use the correct size and grade of battery, ensuring correct polarity (+ and -). Remove used batteries promptly and remove the battery if the remote is not used for an extended period.
• Troubleshooting: The manual provides guidance for common issues such as the LED strip not lighting (checking power supply, connections, polarity, remote battery, and range) or only part of the strip lighting (checking connection points).
• Warranty: The product comes with a three-year limited warranty covering defects in materials and workmanship under normal use and service. The warranty does not cover damage from misuse, abuse, accident, modifications, alteration, neglect, mishandling, improper installation, or normal wear and tear on the finish.
• Recycling: Electrical waste should not be disposed of with household waste; users are encouraged to recycle where facilities exist.

Armacost Lighting RibbonFlex PRO 451200 Specifications