Armacost Lighting RibbonFlex PRO - User Manual

SAFETY INFORMATION
■
DANGER: Risk of eye damage. Do not stare directly at the LED chips
of this LED strip.
■
CAUTION: Do not power LED tape while coiled on reel.
■
IMPORTANT: Always observe polarity for 12-volt connections, positive
(+) to positive and negative (–) to negative.
■
IMPORTANT: Do not install Class 2 low voltage wiring in the same runs
as AC main power. If AC and low voltage wires cross, keep them at
90-degree angles. Use only insulated staples, plastic ties, or wire
support clips to secure cords and wires.
■
NOTICE: LED fl exible tape lighting rating: 12VDC 3A.
■
Only use the 12-volt LED lighting power supply which has been
provided with this kit.
■
Do not bend, crush or pull the cable. Protect from sharp edges,
oil and heat.
■
For indoor/dry location use only.
■
Ensure the connectors are securely fastened before operating the tape.
■
Electrical waste should not be disposed of with household waste.
Please recycle where facilities exist.
Three-year limited warranty
WHAT IS COVERED
The manufacturer warrants this fi xture to be free from defects in materials
and workmanship for a period of three (3) years from date of purchase.
This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be
defective, the manufacturer’s only obligation, and your exclusive remedy, is
the repair or replacement of the product at the manufacturer’s discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifi cations, alteration, neglect, or mishandling. This warranty
shall not apply to any product that is found to have been improperly
installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the
product as a result of an accident, misuse, abuse, negligence, alteration,
faulty installation, or any other failure not relating to faulty material or
workmanship. This warranty shall not apply to the fi nish on any portion of
the product, such as surface and/or weathering, as this is considered normal
wear and tear.
WHAT IS NOT COVERED
The manufacturer does not warrant and specifi cally disclaims any warranty,
whether expressed or implied, of fi tness for a particular purpose, other than
the warranty contained herein. The manufacturer specifi cally disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/ expense costs involved in
the replacement or repair of said product.
Contact customer support at 410-354-6000, support@armacostlighting.com,
or visit armacostlighting.com/support.
Installation considerations
■
Where will you locate your power supply?
■
How will you run and conceal the wires to your LED tape lighting?
■
What is the best mounting position for the LED tape light to achieve
your desired effect?
■
See the section titled “Mounting options” for cabinet lighting
placement tips.
PACKAGE CONTENTS
Plug-in power supply
RF receiver and 8.2 feet
LED tape light (pre-assembled)
RF dimmer
remote
SureLock Wire Lead Connectors (optional use)
Wire support clips
INSTALLATION
Cutting the tape light or extending the tape
light length (optional)
■
Using the provided connectors, this tape light system can be
extended to a total length of up to 5m
■
Use only Armacost RibbonFlex Pro item #142210 (sold separately)
to extend the tape length
■
Additional connectors are available through the point-of-purchase
or directly from armacostlighting.com
■
IMPORTANT: Make sure to observe polarity when making connections,
positive to positive and negative to negative. Check to see that the
wire colors and the polarity markings printed on the tape line up.
Positive
Negative
■
To use the included SureLock Connectors, cut the LED tape with
scissors in the center of a copper pad (position A) as shown, or attach
the connector to the copper pad found at the end of the tape.
■
The tape can also be cut at silver solder joints (position B), but this
cut point should be used for soldered connections only.
Cut tape at
center of
copper pads
B
Okay to cut at solder
joints, but do not
use connector
A
■
Use a SureLock Connector to make turns and go around corners. They
can also be spliced and extended for gaps of any size. 18–20 AWG
wire is recommended for custom lengths (not included).
(
+
)
(
–
)
length to
fi t needs
(
–
)
(
+
)
(
–
)
(
+
) (
+
)
(
–
)
(
–
(
+
+
)
–
)
NOTE: Be sure all 12-volt connections are secure and protected from
electrical shorting. Options include electrical tape, small wire nuts, crimp
connectors, etc.
1
LED Tape Light Kit
Item
451200

Summary

Safety Information and Precautions

Eye Damage Warning

Do not stare directly at LED chips to avoid eye damage. Power LED tape only when uncoiled.

Polarity and Wiring Guidelines

Observe polarity for 12V connections. Keep low voltage wiring separate from AC power.

Product Specifications and Handling

Note 12VDC 3A rating. Use provided power supply. Avoid bending or crushing cable.

Usage and Disposal

For indoor/dry locations only. Ensure secure connectors. Recycle electrical waste properly.

Limited Warranty Details

Warranty Coverage

Covers defects in materials/workmanship for three years for original purchasers. Repair or replacement is at manufacturer's discretion.

Warranty Exclusions

Excludes damage from misuse, accident, alteration, neglect, improper installation, or normal wear.

Installation Planning and Options

Location and Routing

Plan power supply location and wire concealment for desired lighting effect.

Cutting and Extending Tape Light

Cut tape at copper pads or solder joints. Extend up to 5m using specific connectors.

Installation Procedures

Using SureLock Connectors

Open connector, slide tape under contacts, ensure secure closure. Test connection.

LED Strip Installation

Remove backing, press tape firmly. Secure cables with clips. Avoid sharp bends.

Power Supply Installation

Connect AC cord to outlet. Do not power while on reel. Use with compatible dimmer only.

Direct Wiring Power Supply

Disconnect power before wiring. Connect wires to terminal block per local codes.

Assembly Location Preparation

Temporarily position tape light before applying adhesive backing.

Advanced Installation and Mounting

Above Cabinet Uplighting

Mount tape on a strip for indirect lighting. Angle for desired illumination, move away from walls.

Surface Mounting Options

Drill holes for continuous runs, mount behind cabinet lip for work surfaces, or use trim.

Operation and Remote Functions

Remote Control Usage

Pull battery tab. Remote works without line-of-sight. Range up to 50 feet.

Remote Button Functions

Control power, brightness, presets, and dynamic effects via remote buttons.

Pairing, Battery, and Maintenance

Pairing Multiple Kits

Pair additional kits to a single remote by holding buttons during power restoration.

Changing Remote Battery

Replace CR2025 battery by sliding out tray. Ensure correct polarity and usage.

Care and Cleaning

Clean with a dry or slightly damp cloth. Avoid chemicals and abrasives.

Troubleshooting Common Issues

LED Strip Not Lighting

Check power supply, connections, polarity, and remote battery. Ensure correct pairing.

Partial Lighting or Fuse Blows

Check connection points for faults or exposed wires. Ensure correct wiring and circuit protection.

Regulatory Compliance

FCC Statement

Device complies with FCC Part 15. Avoid harmful interference. Modifications may void authority.

Armacost Lighting RibbonFlex PRO Specifications

General

Input Voltage	24V DC
CRI	90+
Cuttable	Yes
Warranty	5 years
Product Type	LED Tape Light
LED Type	SMD
Available Colors	Red, Green, Blue, Amber
Beam Angle	120°
IP Rating	IP20
Cutting Interval	Every 2 inches
Width	10mm
Flexibility	Highly Flexible
Dimmable	Yes
Length	16.4 ft (5 meters)
Operating Temperature	-4°F to 140°F (-20°C to 60°C)