The ES8100 V-Lock is an electromechanical locking device designed for various door applications, including fire and smoke-resistant doors. It functions as an installation guide and user manual, providing comprehensive information for its proper setup, operation, and maintenance.
Function Description:
The ES8100 V-Lock operates as either a Power to Open (PtO) or Power to Lock (PtL) device, depending on the selected locking function. In the PtO configuration, the lock is released when power is applied, making it fail-secure. In the PtL configuration, the lock is engaged when power is applied, making it fail-safe. The lock features a bolt that extends and retracts to secure or release the door. It incorporates a lock status monitor and a door position monitor to provide feedback on its operational state and the door's position. An integrated LED indicator provides visual cues regarding the lock's status and any potential errors. The lock is designed to be installed either horizontally or vertically, with specific orientation requirements for vertical mounting as indicated on the product label. It is crucial never to mount the V-lock in the floor.
Important Technical Specifications:
- Power Supply: 11-26VDC
- Operating Current:
- Peak: 1000mA @ 12VDC
- Standby: 35mA @ 12VDC (with LED activated)
- Lock Status Monitor: NO / NC contacts (50mA @ 30VDC)
- Door Position Monitor: NC (50mA @ 30VDC)
- Maximum Door Side Load:
- Unlocking: 100kg (3-wire mode), 15kg (2-wire mode)
- Locking: 20kg (12W), 35kg (24W)
- Operating Temperature: -10 to 55°C
- Mass: 750g
- Dimensions: 256 x 30 x 42mm
- IP Rating: IP53
- Cable Gauge Requirements: Vary by distance, ranging from AWG22 (0.33mm²) for 5m to AWG12 (2.05mm²) for 50m.
Usage Features:
- Lock Function Setting: The lock function (PtO or PtL) is selected via a slide switch at the rear of the lock. Changes to this setting take effect after the lock is completely powered down (approximately 2 minutes without power) and then re-powered.
- Indication LED Activation: The lock is supplied with the indication LED activated. To activate or deactivate the LED, power the lock through USB or the main connector. Press and hold the push button for 3 seconds to enter setup mode. Short press the button to select illumination colour or deselect LED activation. The lock cycles through the LED indication table with each short press, displaying the secure illumination colour for 1 second to indicate the setting change. Pressing the button for 3 seconds exits setup mode. The LEDs will no longer illuminate white and will begin to illuminate according to the power supplied and lock status. Setup mode times out after 60 seconds if no action is taken.
- Wiring: A 3-wire operation is recommended for optimal performance. A 2-wire operation is possible only in PtL setting, but the lock will operate slower. It is essential to ensure a common ground reference for both power (red) and control (blue) cables.
- Installation: The lock can be installed in timber frames or hollow frames. Specific preparation instructions and dimensions are provided for each type of frame. It is crucial to connect the power cable and complete the lock setting and LED activation before securing the lock with screws.
- Troubleshooting: The lock includes a self-monitoring system that uses the indication LED to warn users of potential issues. Error indicators include slow flashing yellow (voltage drop), blue (lock jam), purple (motor over current), orange (over voltage), yellow (under voltage/over voltage), fast flashing red (2-wire unlocking time-out), slow flashing blue (under temperature), slow flashing red (over temperature), slow flashing red and blue (system fault warning), and fast flashing red and blue (critical system fault). A heart beat LED (slow flashing blue) under the small screw in the cover plate confirms correct power and operation.
Maintenance Features:
- Cleaning: The external surfaces of the lock should be cleaned with a dry cloth only; harsh chemicals should not be used.
- Repairs and Returns: This product contains no user-serviceable parts. For repairs or returns, contact the local supplier.
- Storage and Transport: The product should be transported and stored in its original packaging.
- Dismantling & Environment: The product contains materials that may be hazardous to the environment (Lead, Lead compounds, Chromium, and Nickel). It should not be treated as household waste. Instead, it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. In countries within the European Union, Norway, Iceland, and Liechtenstein, the product is marked with a symbol indicating separate collection. Disposal of packaging and product in a responsible manner helps prevent negative consequences to the environment and human health.
- Fault Diagnosis: The troubleshooting guide provides specific actions for various LED error indicators, such as measuring voltage, checking strike plate alignment, and ensuring proper environmental conditions.
- Product Information: Detailed product information, including fire/smoke test reports and certificates, can be found online at www.assaabloy.com/au/en/solutions/products/electromechanical-locking/es8100-v-lock. For further assistance or if a certificate is not listed, contact the supplier.
Need help?
General
To Next Page