User Guide
Card Key / PIN Code / Key
YDM3115A
16. Automatic/Manual Lock Setting
17. Unlocking Door with Fake Code
Automatic Lock Setting
Manual Lock Setting
Release the button to set automatic lock mode on the main-body
(after opening the battery cover)
Press the button to set manual lock mode on the main-body.
Palm touch
Palm touch Enter the
User PIN Code
Enter the
button for 5 Sec.
Palm touchEnter the user code
and fake code
Enter the Fake Code
and User code
OR
18. External Forced Lock
19. Volume Setting
20. 3-minute Lock Out Feature
21. Alarm
External Forced Lock Setting – User Code
External Forced Lock Setting – Card Key
Contact Card Key on [Card Key reader] for 5 sec. until you
hear 3 beeps.
Releasing External Forced Lock Setting
When the door is unlocked from outside based upon proper
authentication, the External forced lock will be released.
22. Emergency power supply for discharged batteries
Replace 9V
Batteries
Palm touch Touch
Card Key
OR
The operation sound volume will be adjusted
according to the Volume Switch setting.
Intrusion Alarm :
The alarm goes off when someone forces the door open.
For example, In case of an intrusion by opening a gap
in the door while the door is locked.
Broken Alarm :
The alarm sounds when the front part is completely
separated from the main set. For example,
forced removal of external product (front body).
24. Code Chart
Duplicate if necessary
25. Master Mode
Master mode is a mode in which only the administrator can set the door lock and provide
access to other users. 100ea user passwords, 100ea card keys and individual
registration and
deletion of one-time passwords enable efficient management of visitors.
Enter the registered User code.
Press button for 5 seconds.
Touch the registered Card key.
If an invalid user code or card key is entered five(5) times in a row,
lock out mode is activated and all buttons on the front body are not activated
for three minutes.
Open with inside door bar.
Open the door with mechanical key.
Press button.
PIN Code Management(Up to 100 Users.)
: Low : Mute: High
Continue / Complete
Change
Mode
New
Again
Switch to master mode (from normal mode)
PIN CODE
U
PIN CODE
M
PIN CODE
M
OR
Registr
-ation
New
Again
Master Pin Code Change
PIN CODE
M
PIN CODE
M
PIN CODE
M
Delete
OR
Registr
-ation
User Code
PIN CODE
U
UN
OR
UN
PIN CODE
M
Up to 100EA
Only 1EA
Delete
OR
Registr
-ation
Card Key
UN
OR
UN
PIN CODE
M
Up to 100EA
Delete
Registr
-ation
Onetime Code
OR
OR
PIN CODE
M
PIN CODE
M
PIN CODE
O
Only 1EA, Automatically deleted after use
OR
Delete
Delete all credentials
PIN CODE
M
PIN CODE
M
Change
Mode
New
Again
Switch to normal mode (from master mode)
PIN CODE
U
PIN CODE
U
PIN CODE
M
14 (Registration process)
1
Registr
-ation
Bluetooth setting (Yale Access app)
PIN CODE
M
Delete
Registr
-ation
Remote Contoller
OR
OR
PIN CODE
M
Up to 5EA
UN
UN
Button
SET
Delete
Registr
-ation
Home Network Controller
OR
OR
PIN CODE
M
roller
Cont
PIN CODE
M
Set up a new device in the app
To turn off alarm
To Release 3-minute Lock Out
23. Power supply
One-on-one real life size
1.5V(LR6) Alkaline AA Battery
The product uses four 1.5V Alkaline
AA batteries. They may sustain
1 year if used 10 times a day.
(Users are advised to use authentic
Alkaline batteries.)
You must replace all 4 batteries in the following cases:
* The Low Battery LED on keypad flickers red.
* When low battery notification message is played.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE NATIONAL CODE OR RECYCLING
PROGRAM.
•
Do not install the digital door lock in an outdoor environment.
•
Do not attempt to disassemble the digital door lock by your self.
By doing so, you may get an electronic shock and damage the product.
•
Do not use force with a tool onto the product.
•
Make sure to lock the door tight when you go out.
•
Be careful not to hit the handle as it may cause injuries.
•
Do not use water and any type of solvent to clean the product
such as gasoline or benzene as they can cause damage to
electronic circuit, deterioration and or paint peel-off.
•
It is recommended to change User Code on a regular basis.
•
In manual lock mode, make sure to double check
whether the door is securely locked.
•
When External Forced lock is set and unlock the door,
the alarm will be activated.
•
Do not use rechargeable batteries.
Only alkaline batteries are recommended.
•
Make sure to follow the above instructions to avoid any injuries.
•
It cannot be guaranteed in a special conditions & environment such as
water condensation, seaside.
ISL-2007-00
Do not install the digital door
lock in an outdoor environment.
26. Important notes
Do not attempt to disassemble
the digital door lock by yourself.
Do not spray water directly
or wipe with chemicals such as
benzene, gasoline or alcohol.
Do not use force with a tool
onto the product.
When using, remember that
someone else can see the
password.
Make sure to lock the door tight
when you go out.
PLEASE READ INSTRUCTIONS BEFORE USE.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
Packaging of this product can be recycled.
27. Safety and Warning
※ All registered passwords and other credentials can be deleted at the time of mode change.
※ Please install(register) the network module when you want to use a remote control or home network.
User Slot Number should be 2 digits.
like ‘01’ … ‘99’ and ‘00’: Location of 100th user slot must be assigned "00" instead of "100".
※