Asset SORGENTE User Manual

Rev. February 2012 - Code A-Man03
ENGLISH
Installation, User and
Maintenance Manual
WARNING: Read this manual before operating
MADE IN ITALY
prodotto conforme
D.M.174/2004
ASSET S.r.l. Loc. Isola del Pero, 16 - 17041 - ALTARE (SV) - ITALY
Tel: +39 019 58 48 30 Fax: +39 019 51 42 186 - e-mail: info@assetitalia.it - www.assetitalia.it
SMILE
SORGENTE
UNDERCOUNTER
ISI-T

Asset SORGENTE Specifications

General

Weight	15kg
Water Types	Hot, Cold
Material	Plastic, Stainless Steel
Cooling System	Compressor
Power Consumption	500W
Voltage	220V
Frequency	50Hz

Summary

Introduction

1.7 Manufacturer's Responsibility and Warranty

1.7.1 Warranty Terms

Details the specific terms and conditions of the product warranty.

1.8 Technical Assistance Service

Information on contacting technical support and required details for service.

Safety Requirements

3.1 General Notes

Provides essential safety guidelines for operating the dispenser.

3.3 Safety Warnings

Lists critical safety warnings for installation, use, and maintenance.

Installation

5.1 Environmental Characteristics

5.3 Positioning

5.4 Connections

5.4.1 Outer Accessories (all models)

5.4.2 Connection to the Water Mains

Detailed steps for connecting the dispenser to the water supply.

5.4.2 Connection to the Water Mains (cont.)

Specifies requirements for water mains connection, including pressure and fittings.

5.4.3 Power Supply Connection

Instructions for safely connecting the dispenser to the electrical supply.

5.4.4 Connection of Internal CO2 Bottle

Step-by-step guide for connecting the internal CO2 bottle.

5.4.6 Connection of External CO2 Bottle

5.4.6 Connection of External CO2 Bottle (cont.)

Dispenser Use

6.1 Touch Screen User Interface

Overview of the touch screen keypad and its functions.

6.1 Touch Screen User Interface (cont.)

How to interact with the touch screen for dispensing and controls.

6.1.1 Anomalies Signalling Led

6.1.2 Display

Details display information and how alarms are presented.

6.2 Water Temperature Adjustment

6.7 First Start Up

Steps to perform after installation before first use.

6.7 First Start Up (cont.)

Continuing initial start-up, including dispensing water.

6.8.1 Procedure for Starting-Up the Hot Water Boiler

Steps to start and operate the hot water boiler function.

6.8.2 Setting the Refrigerator Temperature

6.8.6 Technical Assistance

Trouble Shooting

7.1 Signallings

Overview of how the dispenser signals failures and anomalies.

7.1.1 List of Signallings

Detailed list of LED signals, their events, and corresponding notes.

7.1.1 List of Signallings (cont.)

Detailed explanations for specific fault codes (A1, A4, B1, B2, E00, E02/E12).

7.2 Solutions to Problems

Table of common operational problems and their user-solvable solutions.

7.2 Solutions to Problems (cont.)

Addresses problems related to sparkling water dispensing, like gas pressure.

7.3 Alarm Signalling for Undercounter Model

7.3.1 Setting and Signalling of Alarms for Models with Remote Control Keypad

7.3.4 Signallings and Acoustic Alarms

Describes filter exhaustion, refrigerator, pump blockage, and smart card errors.

7.3.5 Resyncing of the Remote Control

Maintenance

8.1 Ordinary Scheduled Maintenance Cycles (HACCP)

Outlines routine maintenance tasks and their frequencies.

8.2 Replacement of the Monouse or Rechargeable CO2 Bottle

8.2.1 Replacement of the Internal Monouse Bottle

8.2.2 Replacement of the Rechargeable Bottle

8.3 Filter Replacement

Procedure for replacing the water filter cartridge and its smart card.

8.6 Water Dispenser Sanitization

Steps for sanitizing the dispenser to prevent bacterial contamination.

8.6.1 Dispenser Sanitization Procedure

Detailed steps for performing dispenser sanitization using a kit.

8.6.1 Dispenser Sanitization Procedure (cont.)

Final steps for sanitization, including dispensing water and checking for chlorine flavor.

Spare Parts

10.1 Identification and Ordering Modes