To Next PageTo Next Page
Need help?Do you have a question about the AstroStart RSS-2524 and is the answer not in the manual?
General| Brand | AstroStart |
|---|---|
| Model | RSS-2524 |
| Category | Remote Starter |
| Language | English |
General safety guidelines for operating the remote engine starter and vehicle.
Safety precautions specific to vehicles equipped with manual transmission.
Steps for performing the safety sequence using the parking brake.
Steps for performing the safety sequence using the remote control.
Instructions for selecting transmission channels on the remote.
Guide on how to replace the batteries in the remote control.
Explanation of the pager function for locating or calling remotes.
Details on the PANIC command and its confirmations.
Command for starting the engine and continuous operation.
Command to stop the engine or current mode.
Command for locking doors and arming the security system.
Command for unlocking doors and disarming the security system.
Command to open the trunk or hatchback.
Command to check the system status.
Command to activate or deactivate the sentinel mode.
Command to locate the vehicle in a parking lot.
Command to set the engine runtime duration.
Commands to control various vehicle accessories.
Command to activate or deactivate Valet Mode.
Command to lock or unlock the remote keypad.
Command to enable or disable remote transmitter audible feedback.
Command to toggle between command groups.
How the system confirms commands via horn or parking lights.
Types of confirmations received from the remote transmitter.
Procedure for starting the vehicle's engine using the remote.
Troubleshooting steps if the engine fails to start remotely.
Important steps when entering the vehicle after remote start.
Details on automatic engine stop after a preset time and parking light status.
Information about the negative trigger input for external control.
Instructions for Continuous Mode with automatic transmission vehicles.
Instructions for Continuous Mode with manual transmission vehicles.
Explanation of Turbo Mode for engine cooldown and its activation.
Conditions and reasons why the engine will stop or not start remotely.
Information on the main ON/OFF switch for controlling start functions.
How to use the STOP command to end run time or panic mode.
Details on automatic engine starting based on low temperature.
Procedure for setting the engine runtime duration using button presses.
Explanation of the vehicle's protection zones and their functions.
How the system uses deterrents like siren and lights during a violation.
Description of WARNING, PRE-ALARM, and ALARM CONDITION modes.
Description of the Active mode for arming and disarming the alarm.
Explanation of Semi-Passive rearming and its conditions.
Details on Passive rearming and the rearming cycle.
Commands to stop or disarm the alarm condition.
How system confirmations (chirps, flashes) indicate status.
Table explaining zone codes indicated by parking light flashes.
How the indicator light shows system status and zone violations.
Function to prevent automatic locking when key is in ignition.
How to temporarily cancel automatic rearming for maintenance.
Procedure for permanently deactivating the alarm system for servicing.
Definition and function of the siren.
Definition and function of the horn.
Function of parking lights for confirmations and alarms.
Definition of a violation in the security system.
How the dome light is activated upon commands.
Procedure for locking doors and arming the security system.
Procedure for unlocking doors and disarming the security system.
How to release the vehicle's trunk using the remote.
Explanation of automatic door locking and unlocking based on ignition status.
Details on the antitheft system and its circuit disabler function.
How passive arming type antitheft system operates.
How active type antitheft system operates.
Deactivating the antitheft function using Valet Mode.
How the indicator light displays safety sequence and system status.
Commands to control various vehicle accessories like headlights.
Function to locate the vehicle by sounding horn and flashing lights.
How to enable or disable silent mode for remote control confirmations.
How to lock or unlock the remote control's keypad.
How to activate panic mode for emergency situations.
Table of codes indicating reasons for remote start failure.
Codes indicating which protection zone caused an alarm condition.
Procedure for programming new remote controls to the system.
Procedure to check the hood switch for safety.
Safety check for automatic transmission vehicles related to gearshift.
Safety check for manual transmission vehicles related to gearshift.
Procedure to check if the parking brake status is detected correctly.
Procedure to test if door opening correctly breaks the safety sequence.
Instructions for replacing or boosting the vehicle battery safely.
