Atag VA6811RT - User Manual

Questions and Answers

J
Janet JohnsonAug 17, 2025
What to do if my Atag VA6811RT does not start?
- P
  Patricia RamosAug 17, 2025
  If your Atag dishwasher isn't starting, make sure the Start/Stop button is held until the display shows the door open symbol. Also, check that the door is properly closed, the plug is in the socket, the water tap is on, and no fuses/circuit breakers have tripped. Rule out overflow/leaks or a selected Delayed start option. If a whirring sound persists even when power is cut, turn off the water tap, pull out the plug, and call the service division.
A
Albert OwensAug 20, 2025
How to clean dishes in Atag VA6811RT?
- O
  Olivia ArroyoAug 20, 2025
  If your Atag dishwasher leaves dishes unclean, start by removing and cleaning the spray arms. Ensure you're using fresh detergent and the correct dosage for your water hardness. A higher temperature or more powerful wash cycle might be needed. Make sure dishes aren't blocking each other, and that glasses and cups are stable. Finally, check that the filter is correctly fitted.
J
James JohnsonAug 23, 2025
Why does my Atag VA6811RT leave spots on dishes?
- M
  Michael NelsonAug 23, 2025
  If you notice spots or films on your dishes after using your Atag dishwasher, check the salt compartment lid to ensure it's properly tightened to prevent salt leakage. Also, verify that the water softener and rinse aid dosage settings are correct. Ensure the salt compartment is full. If you're washing crystal, use a lower temperature and less detergent to avoid etching.
M
Mary AndersenAug 26, 2025
What to do if water remains in my Atag VA6811RT Dishwasher?
- J
  Jeffrey AndrewsAug 26, 2025
  If water remains in your Atag dishwasher after a cycle, check the drainage hose for blockages or kinks. Ensure the filters are clean, and inspect the drainage pump for any debris.
D
Danielle AndersonAug 28, 2025
Why are dishes not dry after Atag Dishwasher cycle?
- E
  Emily MooreAug 28, 2025
  If your Atag dishwasher leaves dishes not dry enough, try activating the Long dry option and ensure the dishwasher is fully loaded. Check and top up the rinse aid, or increase its dosage. After the program finishes, open the door a little to aid drying.
S
sharibuckAug 31, 2025
Why does my Atag VA6811RT leave a film on dishes?
- P
  Paul SandersAug 31, 2025
  If you find a sticky white/blue film on your dishes after using your Atag dishwasher, the rinse aid dosage setting is likely too high. Reduce the amount, and if you have very soft water, consider diluting the rinse aid 50:50 with water.
J
Justin LewisSep 2, 2025
Why are the touch buttons on my Atag VA6811RT not responding?
- B
  Brian DixonSep 3, 2025
  If your Atag dishwasher's touch buttons aren't responding, wait a moment after opening the door before pressing them. Ensure the buttons are clean and that the door is opened wide enough for the display to light up. Also, check if the child lock is activated.
K
Kimberly OwensSep 5, 2025
Why are there spots on stainless steel in my Atag Dishwasher?
- L
  Laurie RamseySep 5, 2025
  Spots on stainless steel or silver items in your Atag dishwasher can occur if they come into contact during washing or if certain foods like mustard, mayonnaise, lemon, vinegar, salt, and dressings are left on the items for too long. Rinse off these foods promptly or use the Rinse & Hold program. Avoid contact between silver and stainless steel items during dishwashing.
C
Carolyn GarciaSep 8, 2025
How to get rid of bad odour in Atag VA6811RT Dishwasher?
- J
  Justin CardenasSep 8, 2025
  To address a bad odor in your Atag dishwasher, clean around the seals and corners with a washing-up brush and a low-foaming cleaner. If you frequently use low-temperature programs, run a higher temperature program about once a month.
S
Samantha StevensonSep 12, 2025
How to close the door of Atag Dishwasher?
- M
  Melanie MorrisSep 12, 2025
  If your Atag dishwasher door won't close, ensure the baskets are correctly positioned horizontally and that no dishes are blocking them from sliding into place.