Atag VA68211RT - User Manual

Questions and Answers

G
gabrielle00Aug 17, 2025
What to do if Atag VA68211RT Dishwasher does not start?
- R
  reynoldslarryAug 17, 2025
  If your Atag Dishwasher isn't starting, a few simple checks can help. Ensure you press and hold the Start/Stop button until the display indicates the dishwasher is ready. Verify that the door is fully closed. Check your fuse or circuit breaker. Confirm the dishwasher is plugged into the wall socket and that the water tap is turned on. Also, check for any signs of overflow or leaks. Finally, ensure the Delayed start option hasn't been accidentally activated.
J
Janice ComptonAug 20, 2025
How to fix Atag VA68211RT if dishes are not clean?
- E
  Emily HarrisonAug 20, 2025
  If the dishes in your Atag Dishwasher aren't coming out clean, several factors could be at play. Start by checking that the spray arms rotate freely; remove and clean them if necessary. Make sure dishes aren't blocking the spray arms. Ensure you're using fresh detergent, as old detergent can lose its effectiveness. Also, verify that you're using the correct detergent dosage for your water hardness – too much or too little can impact cleaning. Try selecting a higher temperature or a more powerful wash program. Finally, ensure dishes are loaded correctly, avoiding overcrowding or blocking, and that they sit steadily during the cycle.
O
Omar BushAug 22, 2025
Why does my Atag VA68211RT Dishwasher leave spots or films on the dishes?
- E
  edwardsmaryAug 23, 2025
  If your Atag Dishwasher leaves spots or films on your dishes, consider these possible causes. A leaking water softener can be the culprit, so check that the salt compartment lid is properly tightened. Ensure your water softener setting is correct. Also, verify that your rinse aid dosage setting is appropriate. If the salt compartment is empty, refill it. If you're using 3-in-1 detergent, try inactivating the TAB setting and adding salt and rinse aid separately. High temperatures or excessive detergent can also cause etching, especially on crystal, so wash crystal at a lower temperature with less detergent.
B
Bradley WilsonAug 25, 2025
How to improve drying in Atag VA68211RT Dishwasher?
- R
  rreyesAug 26, 2025
  If your Atag Dishwasher leaves dishes not dry enough, there are several potential reasons. Try activating the Long dry option. Make sure you fully load the dishwasher, as a full load optimizes drying. Check and top up the rinse aid, or increase the dosage if it's set too low. If you're using 3-in-1 detergent, try inactivating the TAB setting and adding salt and rinse aid separately. You can also try opening the door slightly after the program finishes to aid drying.
J
Jessica DeanAug 28, 2025
Why does water remain in my Atag Dishwasher after cycle?
- S
  Sarah WaltonAug 28, 2025
  If water remains in your Atag Dishwasher after a cycle, several issues could be the cause. Start by checking the drainage hose for blockages, loosening it at the sink unit's water trap to clear any debris. Ensure the hose isn't kinked or sharply bent. Clean the coarse and fine filters to remove any buildup. Finally, inspect the drainage pump for debris and clean it if necessary.
S
Sandra McguireAug 30, 2025
How to get rid of bad odor in Atag VA68211RT Dishwasher?
- K
  kevinhendersonAug 30, 2025
  If your Atag Dishwasher has a bad odor, it could be due to dirt accumulating around the seals and in corners; clean these areas with a washing-up brush and a low-foaming cleaner. Also, prolonged use of low-temperature programs can contribute to odors, so run a higher temperature program about once a month to help keep the dishwasher fresh.
D
Dennis JohnsonSep 1, 2025
Why is my Atag Dishwasher making a rattling sound?
- M
  Michelle GibbsSep 1, 2025
  A rattling sound during dishwashing in your Atag Dishwasher typically indicates that the dishes aren't correctly placed or that the spray arms are obstructed. Ensure that all dishes are placed securely and not touching each other. Manually spin the spray arms to confirm they can rotate freely without hitting anything.
J
jonesmarySep 4, 2025
What causes a sticky white/blue film on dishes in Atag VA68211RT Dishwasher?
- Y
  yortegaSep 4, 2025
  If your Atag Dishwasher has a sticky white or blue film on the dishes, it's likely due to a rinse aid dosage setting that's too high. Reduce the amount of rinse aid you're using. If you have very soft water, consider diluting the rinse aid 50:50 with water.
J
Jessica BlevinsSep 6, 2025
Why are there spots on stainless steel or silver in my Atag VA68211RT?
- E
  Erin AndersonSep 6, 2025
  If you're finding spots on stainless steel or silver items in your Atag Dishwasher, it could be due to certain foodstuffs like mustard, mayonnaise, lemon, vinegar, salt, and dressings, which can mark stainless steel if left on too long. Rinse these types of food off dishes if you're not starting the dishwasher immediately. Also, avoid contact between silver and stainless steel items during dishwashing, as this can cause spots. Aluminium can also cause spots on dishes.
E
Emily BrooksSep 9, 2025
What to do if I cannot close the Atag VA68211RT door?
- R
  Richard KingSep 9, 2025
  If you're unable to close the door of your Atag Dishwasher, make sure the baskets are correctly positioned horizontally. Also, check that the dishes inside aren't blocking the baskets from sliding properly into place.

Atag VA68211RT Specifications

General

Type	Freestanding
Noise level	44 dB
Water consumption per cycle	9.5 L
Drying Efficiency Class	A
Delay Start	Yes
Half Load Option	Yes
Child Lock	Yes
Place setting capacity	14 place settings
Dimensions (H x W x D)	850 x 600 x 600 mm