Atom 560 User Manual

MULTI INTERNATIONAL GOLD MEDALS &
AWARD WINNING LAWN EDGERS & TILLERS
Operator /
Owner Manual
63900MA
1711
PROFESSIONAL LAWN EDGERS
2 and 4 Stroke Engines models 560 and 580
ACN 000 583 924
• Safety Precautions • Assembling • Service
• Operating and Edging Instructions
Important Manual – Do Not Throw Away
Manual always to be available for reference or
instructing new operators.
Introduction: Gasoline Lawn Edger
This Atom Gasoline Powered Edger is designed to the highest
standards to ensure you many hours of uninterrupted service.
Pay special attention to the safety precautions. Only persons
who understand this Manual are to operate the Edger.
To receive maximum performance and satisfaction from
your Edger, it is important that you read and understand the
maintenance and safety precautions before using the unit.
Contact your Atom dealer or the Atom distributor in your
area if you do not understand or cannot carry out any of the
operating instructions in this Manual.
Atom’s philosophy is to continually improve all of its products.
As a result, engineering changes and improvements are made
from time to time. Appearances may differ between models.
This manual covers information required to operate, maintain
and service this Atom Lawn Edger.
AS WITH ANY POWER TOOL IMPROPER USE CAN CAUSE
SERIOUS INJURY. Make sure this manual is read and carefully
understood before starting or operating this equipment.
The purpose of Safety
Warnings and Notes in
this Manual is to attract your attention to possible dangers and
deserve your careful attention and understanding. The Safety
Warnings in this Manual and on the Edger do not, by themselves,
eliminate any danger. The instructions or warnings they give are
not substitutes for proper accident prevention measures.
Failure to obey a safety warning can
result in injury to yourself and others.
Contents
Safety Warning Labels ....................................... 1
Safety Precautions .......................................... 2-3
Assembling the Edger .........................................3
Parts and Controls ............................................. 4
Fuels and Oils .................................................. 4
Starting and Stopping Instructions ....................... 5
Edging Instructions ......................................... 5-6
Maintenance Instructions .................................... 6
Blade replacement, cleaning Air Filter ................. 6
Shaft & Wheel Replacement ............................... 6
Throttle Trigger Notes ........................................ 7
Lubrication of Gears .......................................... 7
Warranty ......................................................... 7
Parts List and Parts Illustration .......................... 7- 8
The information contained in this manual is also
available at www.atomindustries.com
Advises you of information or instructions vital
to the operation or maintenance of the equipment.
! SAFETY WARNING
! WARNING
! NOTE
Read operators manual
Do not expose motor
to moisture
Wear eye protection
Keep bystanders away
15m (50 feet)
Blade cover label
SAFETY WARNING LABELS
MADE IN AUSTRALIA
ATOM Lawn Edgers have Australian and foreign Patents, Patent Pending, and Design Registrations.
FIG 1
FIG 2
Disconnect the
mains plug if the
cord is damaged
or entangled
ELECTRIC
PRODUCTS
ONLY
PAGE

Atom 560 Specifications

General

Brand	Atom
Model	560
Category	Lawn Mower
Language	English

Summary

Safety Warning Labels Overview

Visual Safety Indicators and Text Labels

Icons and text indicating operator manual, moisture, bystanders, eye protection, and blade cover.

Comprehensive Safety Precautions

Operator Condition and Safety Protocols

Operator must be in good physical/mental health, not under influence of substances.

Clothing, Footwear, and Eye Protection Requirements

Wear sturdy clothing, long pants, nonslip shoes, and eye protection.

Safe Fueling and Refueling Procedures

Refuel outdoors, switch off engine, allow to cool, avoid ignition sources.

Safe Starting and Working Environment Guidelines

Inspect unit, ensure good working order, use both hands, maintain balance.

Professional Edger Assembly Guide

Handle Supports and Tube Installation Steps

Fit AV handle supports and handle tubes using screws and rubbers.

Cross Brace and Handlebar Attachment Procedures

Attach cross brace and handle tubes with bolt, captive plate, and knob.

Throttle Cable and Handlebar Setup

Attach throttle cable, switch wire, and RH throttle handle to the tube.

Edger Height Adjustment Mechanism

Adjust edger height using the handle adjuster for optimal cutting.

Edger Parts and Control Identification

Key Edger Components and Their Functions

Identification of essential parts like handles, throttle, depth adjustment, and blade cover.

Fueling and Lubrication Guidelines

2-Stroke Engine Fuel Mix Requirements

Use 50:1 oil/gasoline mixture. Never run on gasoline alone.

4-Stroke Engine Fuel and Oil Types

Use clean unleaded gasoline and recommended engine oil.

Engine Starting and Stopping Procedures

Cold Start Engine Operation Guide

Steps for starting the engine when cold, including choke and primer use.

Hot or Warm Engine Starting Methods

Procedures for starting the engine when it is already warm.

Flooded Engine Troubleshooting Steps

Steps to clear excess fuel if the engine becomes flooded.

Safe and Effective Edging Techniques

Edger Operation and Movement Basics

Inspect area, adjust height, use two hands, move forward.

Blade Speed and Clutch Engagement

Ensure blade speed is fast under load; clutch engages at higher engine speeds.

Concrete Edge Trimming Techniques

Align edge guide with concrete; lower handles if blade hits concrete.

Skimming and Angle Cutting Edges

Tilting handles to skim blades along concrete edges or for angle cuts.

Edger Maintenance and Care Procedures

Blade Replacement and Installation Guide

Detailed steps for removing and replacing edger blades using specific tools.

Air Filter and Fuel Filter Maintenance

Instructions for cleaning and oiling the air filter and cleaning the fuel filter.

Troubleshooting Common Edger Malfunctions

Blade Rotation and Motor Power Issues

Addresses issues like loose blades, clogged guards, or clutch problems.

Engine Starting and Running Problems

Covers causes for engine not starting or stopping, like ignition or fuel issues.

Professional Edger Parts and Service Information

Edger Parts Catalog Listing

Comprehensive list of all part numbers and descriptions for the edger models.

Service Assemblies for Efficient Repair

Factory-produced assemblies recommended for efficient and cost-effective repairs.

Throttle Trigger Assembly Repair Guide

Step-by-step instructions for repairing the throttle trigger assembly.

Gear Lubrication Details and Intervals

Information on the sufficient lubrication provided for the edger gears.