OZEO
®
ATOMBERG TECHNOLOGIES PVT LTD
Corporate office: Rupa Solitaire, Office No. 1205
Millenium Business Park, Mahape, Navi Mumbai 400 710.
Manufacturing unit: Plot No D -130 A & B, TTC Industrial Area
Shirawane, Navi Mumbai 400 706.
Remote key
Function Description LED status
Power ON /OFF Switches ON the fan LED fades OFF
Switches OFF the fan,
LED fades OFF slowly
1-5 Fan speed Gradual change of LED fades OFF
control speed from low to high
B Boost mode Boost mode speed LED fades OFF
Timer OFF Timer/
•
Fan automatically switches LED blinks
Wakeup OFF/ ON after the set hours
Timer1 - 1 time
Timer (1,2,3 & 6 Hrs).
•
When timer Timer2 - 2 times
key is pressed for first time, Timer3 - 3 times
timer set for 1Hr.
•
If timer for Timer6 - 6 times
1 Hr is already set and timer Timer Disable - LED
key is pressed, then timer is fades OFF slowly
set for 2 Hr. Similarly, 3 and
6 Hr will set.
•
When timer for
6 Hr is already set and timer
key is pressed, it will disable
Timer.
Sleep Reduce speed
•
When sleep key is pressed
Sleep Mode Enable -
of fan by 1 for
first time, sleep mode is
LED fades OFF
enabled. Sleep Mode operates
Sleep Mode Disable -
for 4 Hr duration. After 2 Hr
LED fades OFF slowly
time duration speed of fan is
reduced by 1 and after next
2 Hr time duration speed is
further reduced by 1. Afterwards,
the fan continues to run on a
reduced constant speed. Fan
speed will not reduce below
speed 1.
•
If sleep mode is already set
and sleep key is pressed, it will
disable sleep mode.
LED LED mode When LED key is pressed for
LED mode enable - LED
first time, it will turn ON LED. glows continuously
If LED is ON and LED key is LED mode disable -
pressed, it will turn OFF LED. LED OFF
Problem Cause Solution
Fan is Nut holding motor Securely fasten the nut and bolts along with
wobbling shaft and the down washers as per the instructions provided in this
rod is loose manual.
Nut holding down Securely fasten the nut and bolts along with
rod and shackle kit washers as per the instructions provided in this
is loose manual.
Screws in shackle kit Securely fasten the nut and bolts along with
and the ceiling hook washers as per the instructions provided in this
are loose manual.
Fan blades are not
A common mistake is fixing the blade in the
seated properly on reverse direction. Please set it right and securely
the motor fasten the screws.
Fan blades are out Make sure that the blades are not bent during
of balance
cleaning. Also, interchanging them helps balance
the blades.
Restart/ Regulator not Make sure the regulator is
eliminated from the
speed bypassed
connection.
variation
Blades have wrong Check the sweep of blades with the fan sweep
sweep before assembling.
Problem Cause Solution
Fan does Fuse down / MCB Check fuse of the MCB on the mains.
not start shut off
Loose wire connection Check the wire connection and restore the
to fan or to the switch connection
on the panel
Fan still does not start Please contact the service number provided.
Regulator is connected
It is recommended that the regulator should not
to the fan
be connected to this ceiling fan and it is instead
controlled using the remote provided with it.
Fan Bearing inside This ceiling fan is designed to be longlasting.
making the housing However, after many years of use the bearing
noise has problems may wear off and may need to be replaced.
Fan blades are not
Make sure the blades are properly fastened to the
seated properly on body. Loose connection may cause accidents.
the motor
Shackle kit rattling Make sure that the screws and nuts are securely
fastened along with washer provided.
Canopy is touching Make sure that the canopy and the wire that
the body connects the fan are not touching the body of
the motor.
Canopy is touching Make sure that the canopy is not touching the
the ceiling ceiling.
Note:
Sleep mode will not work if fan is off.
SLEEP mode adds smart comfort, as the temperature drops over the night and if
you wish to auto-reduce the speed.
With TIMER mode, you can switch OFF/ON the fan automatically after set hours to
further save energy.
DO NOT use the fan regulator as the fan is operated using a remote.
Eliminate the regulator by using a direct connection from the switch to the fan.
WARNING
TROUBLESHOOTING
Your ceiling fan is designed to be longlasting with a strong body and well-tested
electronics, however if any problem arises, please refer to the guidelines shared.
Please contact a local electrician or service engineer if you need any help.
MAINTENANCE
Periodic cleaning of your ceiling fan is the only maintenance needed.
When cleaning, use only a soft lint-free cloth or brush to avoid scratching the
smooth paint finish. You can use moist cloth to remove stains if any. However, do
not use water directly. Abrasive cleaning agents are not required and should be
avoided to prevent damage to the outer finishing.
WARNING
Do not use water when cleaning your ceiling fan. It could damage the motor by
causing short-circuit and create the possibility of an electrical shock.
Do not bend the blades while cleaning. A bend in the blade may result in unstable
fixing and affect the air delivery.
INSTRUCTION
MANUAL
IMPORTANT NOTE:
Read this manual carefully before installing or
operating your new Atomberg OZEO
®
Ceiling Fan.
Ensure you save this manual for future reference.
290mm X 210mm: same size artwork
B
O
O
S
T
,
S
L
E
E
P
&
T
I
M
E
R
M
O
D
E
R
E
M
O
T
E
W
I
T
H
To Next Page
Need help?
General
