6
Disconnect
plug from
power outlet
Unplug the power plug of the specified charger (sold
separately) from the outlet when not in use.
Leaving the power plug plugged in might cause fire, burns,
injury, electric shock, etc.
Disconnect
plug from
power outlet
If water or other liquids (drinking water, sweat, seawater,
pet urine, etc.) enter, unplug the power plug from the
outlet immediately.
Failure to do so might cause fire, burns, electric shock, etc.
Disconnect
plug from
power outlet
Before cleaning, unplug the power plug from the outlet.
Cleaning without unplugging the power plug might cause
fire, burns, electric shock, etc.
CAUTION
Prohibited
Do not touch the specified charger (sold separately) for a
long period when it is plugged into the outlet.
Doing so might cause burns, etc.
Instruction
If you feel any skin abnormalities associated with use of
the specified charger (sold separately) or desktop holder
(SHV36PUA), discontinue use and consult a doctor
immediately. Use of the product might cause itchiness,
skin irritation, rashes, etc. depending on your physical
condition.
For the materials used for the desktop holder (SHV36PUA),
refer to "Materials" (
▶
P. 6).
au Nano IC Card 04
CAUTION
Instruction
When handling the au Nano IC Card 04, be careful with
cut edges so as not to damage your finger or any other
part of your body.
Failure to do so might cause injury, etc.
Instruction
Be careful when inserting/removing the au Nano IC Card
04.
Failure to do so might injure your hand or finger.
Use near Medical Devices and Inside Medical
Facilities
WARNING
Instruction
If you are using an electronic medical device such as an
implanted pacemaker or implanted cardioverter-
defibrillator, carry or use the product at least 15 cm away
from where the device is.
Radio waves might adversely affect the operation of the
electronic medical device.
Instruction
Before using an electronic medical device other than an
implanted pacemaker or implanted cardioverter-
defibrillator outside a medical institution (for home
treatment, etc.), check with its manufacturer on radio
wave effects.
Radio waves might adversely affect the operation of the
electronic medical device.
Instruction
In a situation where you may not be able to maintain a
distance of at least 15 cm from other persons, such as
when your movement is restricted, disable radio wave
emission by setting Airplane mode, turning off the
product, etc.
There may be persons with an electronic medical device
such as an implanted pacemaker or implanted
cardioverter-defibrillator nearby. Radio waves may
adversely affect the op
eration of the electronic medical
device.
Instruction
Regarding the use of the product in a medical institution,
follow the instructions given by the medical institution.
Failure to do so might adversely affect the operation of
electronic medical devices.
Materials
Main Unit (SHV36)
Part Material
Surface
treatment
Display surface Reinforced glass AF coating
Back
PC + ABS (GF20%)
Acrylic UV cured
coating
Outer casing PA resin + GF45% Acrylic UV cured
coating
Power key PC Acrylic UV cured
coating
Volume up/down key PC Acrylic UV cured
coating
Shutter key Aluminum Anodizing
Phone key, Home key, Mail
key
PC + PMMA Hard coating
Periphery of Phone key,
Home key, Mail key
PC + PMMA Hard coating
Camera slide c
over PC + ABS Acrylic UV cured
coating
Camera panel Reinforced glass
AR coating + AF
coating
Camera fringe Aluminum Anodizing
Mobile light lens PC None
Screen for earpiece (receiver)/
speaker
Polyester None
External connection jack
(resin portion)
PA resin None
External connection jack
(metal portion)
SUS + copper
alloy
Tin plating, gold
plating
Charging terminals SUS Gold plating
Strap pin SUS None
au Nano IC Card 04/microS
D
memory card cover
PC resin Acrylic UV cured
coating
Hinge of au Nano IC Car
d 04/
microSD memory card cover
Elastomer resin None
Seal on au Nano IC Card 04/
microSD memory card cover
EPDM None
au Nano IC Card 04 tray slot SUS None
microSD memory card slot SUS Nickel plating
au Nano IC Card 04 tray POM resin None
IMEI tray PET resin None
Camera fringe sheet Acrylic resin + PET
resin
Hard coating
Desktop Holder (SHV36PUA)
Part Material
Surface
treatment
Outer casing (top/bottom) ABS resin Emboss
processing
Lock lever POM resin None
Contact lever POM resin None
Charging terminals (positive
and negative pins)
Phosphor bronze Gold plating
External connection jack
(resin portion)
SUS None
External connection jack
(metal portion)
SUS None
Rubber foot Urethane foam None
Screw Carbon steel for
cold heading
Trivalent
chromate
Rating plate Polyester f
ilm Lamination
Instruction label Polyester film Lamination
To Next Page
Loading...
