EasyManua.ls Logo

Audio Analogue primo CENTO VT - User Manual

Audio Analogue primo CENTO VT
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
AUDIO ANALOGUE
primo
CENTO VT
INTEGRATED AMPLIFIER
OWNER’S MANUAL
MANUALE D’ISTRUZIONI
Manual rev1.3a
All manuals and user guides at all-guides.com
all-guides.com

Table of Contents

Questions and Answers

  • A
    amy65Aug 3, 2025
    Why is my Audio Analogue Amplifier remote controller not working?
    • H
      Heather MitchellAug 4, 2025
      There are several reasons why your Audio Analogue Amplifier remote might not be working. First, ensure you've selected the correct source using the input selector. Second, check the batteries; they may be missing or worn out—replace them with two new ‘AAA’ batteries. Finally, make sure you're not too far from the unit or at too extreme of an angle. Try moving closer and adjusting your angle relative to the front panel.
  • D
    Dustin FisherAug 12, 2025
    What to do if my Audio Analogue Amplifier has one LED on but no sound?
    • M
      Mrs. Kathleen LopezAug 12, 2025
      If your Audio Analogue Amplifier has one LED illuminated but no sound, there are several potential causes. First, the volume may be set too low, so try increasing it. Second, the signal connectors between the amplifier and your audio sources might be faulty or improperly connected; inspect the cords and their connections. Third, the source may be off or incorrectly selected; ensure the source is active and the correct input is chosen. Lastly, the power connectors between the amplifier and the speakers could be faulty or improperly plugged in; check these cords and their connections as well.
  • W
    William CarrollAug 18, 2025
    How to fix Audio Analogue Amplifier with no LEDs on and no sound?
    • J
      Joshua HudsonAug 18, 2025
      If your Audio Analogue Amplifier shows no LEDs and produces no sound, there are a couple of things to check. First, make sure the power cord is correctly plugged into the wall outlet. If the power cord is correctly plugged in, the problem may be burned-out fuses, in this case contact your Audio Analogue retailer for a fuse check and replacement.
  • J
    James HigginsAug 26, 2025
    What to do if Audio Analogue Amplifier input LEDs and volume control are not working correctly?
    • N
      Nathaniel JordanAug 26, 2025
      If the input LEDs and volume control on your Audio Analogue Amplifier aren't functioning correctly (e.g., input LEDs are on but volume LEDs are off, or vice versa), the issue might be a faulty or incorrectly plugged front panel. Contact your Audio Analogue retailer to have the connections checked and the front panel replaced if necessary.

Summary

Introduction and Safety Precautions

General Warnings

Important safety warnings for operating and maintaining the equipment.

Necessary Safety and Maintenance Precautions

Detailed instructions for safe operation, installation, and maintenance.

Front and Back Panel Descriptions

Front Panel Overview

Description of the controls and indicators on the front panel.

Back Panel Connectivity

Description of the connectors and ports on the back panel.

Operation and Setup

Remote Controller Functions

Explanation of the remote control's buttons and their amplifier functions.

Unpacking and Package Contents

Instructions for unpacking the unit and checking the package contents.

Placement and Installation Guidelines

Recommendations for placing and connecting the Primo Cento VT.

Powering Up and Input Selection

Steps for powering on the unit and selecting audio inputs.

Volume Control and Muting

Instructions on adjusting volume and using the mute function.

Technical Information and Troubleshooting

Phono Cartridge Switchover

Information on switching between MM and MC phono cartridges.

Operating Warnings

Important warnings and precautions for using the Primo Cento VT.

Product Specifications

Technical specifications for the Primo Cento VT amplifier.

Troubleshooting Common Issues

Guidance for diagnosing and resolving common problems with the unit.

Disposal Information

Disposal for Private Households

Information on how private users should dispose of the equipment.

Disposal for Business Users

Information on how business users should dispose of the equipment.

Audio Analogue primo CENTO VT Specifications

General IconGeneral
Input Impedance47 kΩ
Signal-to-Noise Ratio> 90 dB
Inputs4 x RCA, 1 x XLR
TypeIntegrated Amplifier
Input Sensitivity300 mV
OutputsSpeaker

Related product manuals