Need help?Do you have a question about the Audiopipe APCL-1800ID and is the answer not in the manual?
General| Maximum Power Output | 1800W |
|---|---|
| Continuous Power Output 1 Ch @ 4 Ohm | 750W |
| Continuous Power Output 1 Ch @ 2 Ohm | 1150W |
| Continuous Power Output 1 Ch @ 1 Ohm | 1800W |
| Input Level | 0.2 ~ 5V |
| Frequency Response | 8 ~ 180Hz |
| LPF | 40 ~ 180Hz |
| SUBSONIC Filter | 5 ~ 50Hz |
| Bass Boost Frequency | 30 ~ 80Hz |
| Bass Boost Level | 0 ~ 12dB |
| THD at 4 Ohm load 30% Rated Power | <0.2% |
| Signal Noise Ratio | 70dB |
| Best Efficiency | 85% |
| Minimum Load | 1 Ohm |
| Overheat Protect Temperature | 80˚C/176˚F |
General| Maximum Power Output | 3000W |
|---|---|
| Continuous Power Output 1 Ch @ 2 Ohm | 3000W |
| Input Level | 0.2 ~ 5V |
| Frequency Response | 8 ~ 180Hz |
| LPF | 40 ~ 180Hz |
| SUBSONIC Filter | 5 ~ 50Hz |
| Bass Boost Frequency | 30 ~ 80Hz |
| Bass Boost Level | 0 ~ 12dB |
| THD at 4 Ohm load 30% Rated Power | <0.2% |
| Signal Noise Ratio | 70dB |
| Best Efficiency | 85% |
| Minimum Load | 2 x 1 Ohm or 1 x 2 Ohm |
| Overheat Protect Temperature | 80˚C/176˚F |
Proper connection of speaker cables to avoid amplifier damage.
Connection for the +12 Volt power cable with fuse.
Connects to radio remote terminal for automatic amplifier operation.
Chassis ground connection for stable operation.
Adjusts amplifier sensitivity to match source unit output.
Allows volume adjustment from the driver's seat.
Connects to radio RCA outputs for audio signal.
Indicates amplifier operational status or malfunction.
RCA jack for receiving signal when bridged as a slave amplifier.
RCA output for sending bridge signal to another amplifier.
Filters high frequencies to match woofer response.
Filters unwanted low frequencies to improve woofer power handling.
Adjusts the center frequency for bass boost.
Controls the amount of bass boost from 0 to 12dB.
Indicates self-test mode or amplifier malfunction.
Connects amplifier output to speakers.
+12V and Ground terminals for power supply.
Connects to the remote turn-on signal.
Includes Gain, LPF, Subsonic, Bass Boost, and other controls.
Connects amplifier output to speakers.
+12V and Ground terminals for power supply.
Connects to the remote turn-on signal.
Includes Gain, LPF, Subsonic, Bass Boost, and other controls.
Professional installation by an authorized dealer is recommended.
Specifies fuse ratings and wire gauge for each model.
Guidelines for secure mounting and proper cable placement.
Important notes for linking two amplifiers.
Diagram for single speaker mono configuration with APCL-18001D.
Diagram for single speaker mono configuration with APCL-30001D.
Wiring diagram for linking two APCL-18001D amplifiers.
Solutions for when the run indicator does not light up.
Solutions for when the amplifier is on but produces no sound.
Troubleshooting steps for weak bass output.
Solutions for when the amplifier switches on and off repeatedly.
Detailed technical specifications for the APCL-18001D amplifier.
Detailed technical specifications for the APCL-30001D amplifier.
To Next Page
