Autonics SFL Series - Hand Detection (Ø20 Mm)

121 pages

To Next Page

To Previous Page

3. Dimensions

󹮺󹮸󹮺

i.󹮰 -|Transparent󹮰setting󹮰guide|-

󹮺󹮺 󹮶󹮷

󹮴󹮺󹮰󹮵

Main Page

Preface3
User Manual Guide4
User Manual Symbols5
Safety Considerations6
Caution During Use9
Table of Contents10
Table of Content11
Table of Content12
1� Overview13
Features13
Components and Sold Separately13
Components13
Sold Separately13
Ordering Information14
Feature Comparison14
Specifications15
Standard Type15
Advanced Type15
Common16
IEC 61508 Parameters17
IP67G (JEM Standard)17
Models18
Finger Detection (SFL(A)14-□-□, Ø14Mm)18
Hand Detection (SFL(A)20-□-□, Ø20Mm)19
Hand-Body Detection (SFL(A)30-□-□, Ø30Mm)20
How to Calculate the Response Time (RT) for the Series Connection21
3� Dimensions22
Emitter / Receiver22
Fingter Detection (Ø14Mm)22
Hand Detection (Ø20Mm)24
Hand - Body Detection (Ø30Mm)26
Sold Separately28
Brackets28
Power I/O Cable30
Connector Cable31
Y Type Connector Cable32
Series Connection Cable33
Lamp Output Cable33
SFL / SFLA Dedicated USB to Serial Communication Converter33
Test Piece33
Unit Descriptions35
Status Indicators37
7-Segment Display38
Setting Switch39
4� General Functions40
Mode and State40
Self-Test40
Alarm for Incident Light Level41
OSSD Output42
Mutual Interference Prevention42
Change Settings42
5� Safety-Related Function43
Interlock44
Auto-Reset44
Manual Reset44
Wiring47
Change Settings47
Lockout Reset48
Wiring48
External Device Monitoring (EDM)49
Wiring49
Change Settings49
Muting50
Standard Mode50
Exit-Only Mode63
Change Settings68
Override69
Wiring70
Change Settings71
Blanking72
Fixed Blanking72
Floating Blanking75
Use the Floating Blanking with Fixed Blanking Zone76
Change Settings77
Reduced Resolution78
Change Settings79
6. Other Functions80
Series Connection80
Change Sensing Distance83
Change Settings83
Set NPN or PNP84
Setting Change84
External Test85
Wiring85
Auxiliary Output (aux 1/2)86
Wiring87
Setting Change87
Lamp Output (Lamp 1/2)88
Wiring89
Setting Change89
Wiring90
I/O Connection Diagram90
Input Circuit Diagram90
Output Circuit Diagram90
Example of Wiring Diagram91
Wiring Diagram for Interlock and EDM93
Wiring Diagram for Reset-Hold95
Wiring Diagram for Muting97
8. Configuration Software, Atlightcurtain99
System Requirements99
USB to Serial Connection99
9� Installation100
Installation Conditions100
Safety Distance101
Safety Distance According to ISO 13855 (en ISO 13855, KS C 13855)101
How to Install and Adjust Your Light Curtain104
Installation for Mutual Interference Prevention104
When Using a Series Connection104
When Using One Set of the Light Curtain105
About Installation of a Reflective Surface107
Mount Brackets108
Top/Bottom Adjustable Bracket (BK-SFL-TBA)108
Top/Bottom Bracket (BK-SFL-TBF)108
Side Adjustable Bracket (BK-SFL-SA)109
Side Bracket (BK-SFL-SF)109
Cautions When Using the Brackets110
Mount LOTO Device111
10. Check and Maintenance112
Check Installation Conditions112
Check Wiring Connection112
Safety-Related System-Check When the Operation Stops113
Safety-Related System-Check in Operation114
Daily Inspection114
Regular Inspection114
11. Troubleshooting115
Error Code (Lockout Condition)115
Warning Code117
12� Appendix118
Glossary118
Kcs Model119
Manual Revision History120

Autonics SFL Series - Hand Detection (Ø20 Mm)

Table of Contents

Other manuals for Autonics SFL Series