Avanti DGR24P3S - User Manual

Other manuals for Avanti DGR24P3S

Installation Instructions20 pages

Questions and Answers

T
Tyler PetersonAug 16, 2025
What to do if oven or broiler does not heat in Avanti Ranges?
- S
  smitherinAug 16, 2025
  If the oven or broiler in your Avanti Ranges isn't heating, several factors could be the cause. First, ensure the temperature control is set properly to the desired temperature. Also, check if a house fuse has blown or a circuit breaker has tripped; check/reset the circuit breaker and/or replace the fuse (do not increase fuse capacity, and if it's a circuit overload, have it corrected by a qualified electrician). Make sure the range cord is connected to a grounded outlet. If the pilot light will not light due to a power failure, light the pilots manually. Finally, the range may not be set for appropriate gas input; see the range conversion section of the installation manual.
S
simmonsstephanieAug 19, 2025
How to fix inaccurate oven temperature in Avanti Ranges?
- D
  Deanna ShawAug 19, 2025
  If you're experiencing inaccurate oven temperatures with your Avanti Ranges, consider these potential causes. Ensure the oven capillary bulb is positioned properly, snapped in the clips straight, and not touching the sides or coated with oven cleaner or food. Also, verify that the temperature control knob is set at the desired temperature. Improper use of foil could also be a factor; keep foil clear of holes in the oven bottom and off of the oven sides. A blocked vent could also be the issue; keep the vent on the backguard clear. The range may not be set for appropriate gas input; see the range conversion section of the installation manual.
T
tparksAug 25, 2025
Why does the flame burn halfway round on my Avanti Ranges?
- F
  floresericAug 25, 2025
  If the flame on your Avanti Ranges only burns halfway around, it could be due to a few reasons. Burner ports might be clogged; use a small gauge wire or needle to open the ports. Moisture might be present after cleaning; lightly fan the flame and allow the burner to operate until the flame is full, or dry the burners thoroughly following the instructions in the range 'Cleaning' section. The range might not be set for appropriate gas input; see the range conversion section of the installation manual.
C
Christopher BoothAug 27, 2025
How to level Avanti Ranges?
- L
  Larry CannonAug 27, 2025
  To level your Avanti Ranges, start by placing an oven rack in the center of the oven. Place a level on the rack and adjust the leveling legs. If the floor is weak or unstable, ensure it is level and can adequately support the range; contact a carpenter to correct a sagging or sloping floor. Kitchen cabinet misalignment may also make the range appear unleveled; ensure cabinets are square and have sufficient room for range clearance, and contact a cabinet maker to correct the problem.
S
Stephen BaxterAug 31, 2025
Why is the flame orange on my Avanti Ranges?
- M
  Matthew JohnsonAug 31, 2025
  An orange flame on your Avanti Ranges could be due to dust particles in the main line. Allow the burner to operate for a few minutes until the flame turns blue. The range may not be set for appropriate gas input; see the range conversion section of the installation manual.
E
Emily NguyenSep 4, 2025
Why does my Avanti Ranges oven smoke excessively?
- M
  mathisheatherSep 4, 2025
  Excessive smoke from your Avanti Ranges oven could be caused by the meat being too close to the broiler burner; reposition the broiler pan to provide more clearance between the meat and the broiler burner. Another reason could be that the meat was not prepared properly; remove excess fat from the meat.
M
mtapiaSep 7, 2025
How to fix an oven light that doesn't work in Avanti Ranges?
- J
  Janice WilsonSep 7, 2025
  If the oven light in your Avanti Ranges isn't working, it could be due to a burned-out or loose bulb. Try tightening or replacing the oven light bulb.
P
pooleangelaNov 11, 2025
Why won't the surface burners light on my Avanti Ranges?
- R
  Randy GarnerNov 11, 2025
  There are several reasons why the surface burners on your Avanti Ranges might not light. It could be that the surface control has not been completely turned to the ON position; push in and turn the control to the ON position until the burner ignites, then turn the control to the desired flame setting. Another reason might be that the burner ports are clogged; use a small gauge wire or needle to open the ports. Also, make sure burners are positioned properly on the orifice hoods and sitting flat on the burner support with tabs engaged in slots. The range power cord may also be disconnected from the outlet; be sure the power cord is plugged into a grounded outlet. If the pilot lights won’t light due to power failure, light them manually. Finally, the range may not be set for appropriate gas ...