Camera Operation LED
The Axon Body 2 camera’s operation LED displays the system’s current operating
mode.
Operating Mode Operation LED
Recording
Recovering interrupted video*
Blinking red
Buering Blinking green
Booting up/powering down
Error state**
Solid red
*When the Function LED also is blinking red.
**When the Function LED also is solid red.
Camera Function LED
The Axon Body 2 camera’s function LED displays when certain functions are enabled.
Function Enabled Function LED
Mute Blinking blue
Camera error *** Solid red
Bluetooth feature is booting up Solid blue
***Use the power switch to turn the camera o and on.
Battery LED
The camera’s battery LED displays the battery’s remaining capacity, when the device
is being used or when charging.
Battery Status Battery LED
Battery capacity is 41–100% Green
Battery capacity is 20–40% Yellow
Battery capacity is less than 20%
Red during operation; ashing red and
yellow during charging
Battery critically low Blinking red and yellow
Axon Body 2 Quick Start Guide
English
Recording
The Axon Body 2 camera has two operating modes. The default mode, or BUFFERING
mode, provides pre-event buering to capture activities that occur before you activate
the EVENT (recording) mode.
1 Turn the system on. Move the ON/OFF switch to the ON position.
• The camera takes a few seconds to boot up and be ready to record (the red area
under the switch will be exposed with the switch moved to the ON position).
• The operation LED will be solid red and then transition to blinking green when
the system goes into BUFFERING mode.
• The Axon Body 2 camera will go into BUFFERING mode after the boot up
sequence. The BUFFERING mode holds the previous 30 seconds of video [NO
AUDIO] leading up to the beginning of a recording.
Solid Red
Boot Up Mode
Blinking Green
BUFFERING Mode
2 To record, quickly double-press the EVENT button.
• The camera now records audio as well as video.
• The camera will beep twice to let you know that recording has started. The two
beeps will repeat every two minutes (audio notications can be deactivated
if necessary).
• The operation LED will blink red.
3 To add a marker to the video, quickly press and release the Function button.
4 To stop audio recording (mute), press and hold the Function button for three
seconds.
5 To stop all recording and return to BUFFERING mode, press and hold the EVENT
button for at least three seconds until there is a long, audible beep.
With default settings, the system does not capture audio in BUFFERING mode, so
anything recorded in that mode will be video-only. BUFFERING mode starts only
after the camera is turned on. The system does not record when the Axon Body 2
camera is turned o.
EVENT Button
Blinking Red - EVENT Mode
Axon Body 2 Wall Charger (not shown)
Hardware
Axon Body 2 USB Cable
Axon Body 2
Camera
Read, understand, and follow all current instructions, warnings, and relevant TASER training materials before using any Axon system. The most up-to-date
warnings and instructions are available at www.taser.com.
Before using an Axon Body 2 camera, ensure it is fully charged, and connect it to Evidence.com via the Axon Dock or Evidence Sync software to ensure it is
properly congured. See Battery LED and Recharging the Battery and Uploading Data for more information. If the battery is removed or its charge is ever
depleted, recharge and reconnect the camera again.
Quick Reference
Upload Status LED
Bottom View
Camera Lens
Power Switch
Red = On/Buffering
Recharging/Dataport
Data Transfer & Recharging
through PC or Axon Dock
Top View
Operation LED
EVENT Button
Double Tap = Start Record
Hold 3 Sec = Stop Record
Speaker
Battery LED
Green = 41% - 100%
Yellow = 20% - 40%
Red = Less Than 20%
Microphone
Battery Status Button
Push to Show Status of
Battery
Function Button
Mute or add marker
Function LED
To Next Page
Need help?
General
