Baby Lock ellegante 2 BLG2 User Manual (English)

Other manuals for Baby Lock ellegante 2 BLG2

Instruction And Reference Guide268 pages

Additional Accessories Guide8 pages

Questions and Answers:

G
Glenn Jordan Jr.Aug 20, 2025
What to do if my Baby Lock Sewing Machine is skipping stitches?
- T
  Tony ChenAug 20, 2025
  Skipped stitches can occur if the machine is threaded incorrectly, you're using the wrong needle or thread for the fabric, the needle is damaged or installed incorrectly, the needle is defective, or dust has collected under the needle plate. Check the threading, consult the “Fabric/Thread/Needle Combination” chart, replace the needle, reinstall the needle correctly or remove dust with the brush.
L
Lauren DanielsAug 22, 2025
Why does the upper thread keep breaking on my Baby Lock ellegante 2 BLG2 Sewing Machine?
- D
  Dr. James RomeroAug 22, 2025
  The upper thread may break because the machine isn't threaded correctly, the thread is knotted, the thread is too thick for the needle, the upper thread tension is too strong, the needle is damaged or installed incorrectly, or there are scratches on the needle plate, presser foot, or race. Rethread the machine correctly, check needle and thread combinations, adjust the thread tension, replace the needle, replace the needle plate, replace the presser foot, or replace the race.
R
Ricardo ColonAug 25, 2025
Why is the bobbin thread breaking on my Baby Lock ellegante 2 BLG2 Sewing Machine?
- J
  justinwintersAug 25, 2025
  Bobbin thread breakage can be caused by the bobbin being set incorrectly or scratches on the bobbin, or the bobbin doesn’t rotate properly. Reset the bobbin thread correctly or replace the bobbin.
K
Katie DouglasAug 26, 2025
How to fix incorrect thread tension on my Baby Lock ellegante 2 BLG2 Sewing Machine?
- J
  Jade MillerAug 27, 2025
  Incorrect thread tension can result from incorrect upper threading, the bobbin being set incorrectly, using the wrong needle or thread for the fabric, the presser foot holder not being attached correctly, or the thread tension being set incorrectly. Check the threading, reset the bobbin, check the “Fabric/Thread/Needle Combination” chart, reattach the presser foot holder correctly, or adjust the thread tension.
P
Peter HollandAug 28, 2025
Why does the fabric pucker when I sew with my Baby Lock ellegante 2 BLG2?
- K
  Kim WhiteAug 28, 2025
  Fabric puckering can occur due to incorrect threading of the upper or bobbin thread, incorrect spool cap placement, using the wrong needle or thread for the fabric, a damaged needle, stitches that are too long for thin fabrics, incorrect thread tension, or using the wrong presser foot. Check the threading, reattach the spool cap, check the “Fabric/Thread/Needle Combination” chart, replace the needle, shorten the stitch length, adjust the thread tension, or use the correct presser foot.
K
Kayla PooleAug 30, 2025
Why is my Baby Lock ellegante 2 BLG2 making a high-pitched sound?
- A
  arnoldmoniqueAug 30, 2025
  A high-pitched sound while sewing can be caused by dust or lint in the feed dogs, thread pieces in the race, incorrect upper threading, or scratches on the race. Remove the dust or lint, clean the race, check the threading, or replace the race.
W
Willie UnderwoodSep 1, 2025
Why is the needle breaking on my Baby Lock ellegante 2 BLG2?
- A
  Aaron JensenSep 1, 2025
  The needle may break due to incorrect installation, a loose needle clamp screw, a turned or bent needle, using the wrong needle or thread for the fabric, using the wrong presser foot, excessive upper thread tension, incorrect spool cap placement, or scratches around the holes in the needle plate or presser foot, or scratches on the race. Reinstall the needle correctly, tighten the needle clamp screw, replace the needle, check the “Fabric/Thread/Needle Combination” chart, use the recommended presser foot, adjust the thread tension setting, reattach the spool cap, replace the needle plate, replace the presser foot, or replace the race.
M
Matthew BruceSep 5, 2025
Why won't my Baby Lock ellegante 2 BLG2 feed fabric?
- E
  Erin BradleySep 5, 2025
  The fabric might not feed through if the feed dogs are down, the stitches are too close together, the wrong presser foot is being used, or the needle is damaged. Use the feed dog position lever to raise the feed dogs, lengthen the stitch length setting, use the correct presser foot, or replace the needle.
C
Christopher CostaSep 7, 2025
Why won't my Baby Lock ellegante 2 BLG2 Sewing Machine operate?
- K
  Kevin BarnesSep 7, 2025
  The machine may not operate if no pattern is selected, the “Start/Stop” button wasn't pushed, the main power switch isn't on, the presser foot isn't lowered, the “Start/Stop” button was pushed with the foot controller attached, the speed control lever is set to control the zigzag stitch width, or all keys and buttons have been locked . Select a pattern, press the “Start/Stop” button, turn the main power to ON, lower the presser foot, remove the foot controller, or use the foot controller to operate the machine, use the foot controller instead of the “Start/ Stop” button to operate the machine or press to unlock all keys and buttons.
D
Danielle StevensonSep 9, 2025
How to fix character pattern that does not turn out on my Baby Lock Sewing Machine?
- K
  Karl BurnsSep 9, 2025
  If a character pattern doesn't turn out correctly, it could be due to using the wrong presser foot, incorrect pattern adjustment settings, or not using a stabilizer material on thin or stretch fabrics, or thread tension is set incorrectly. Attach the correct presser foot, revise the pattern adjustment settings, attach a stabilizer material, or adjust the thread tension.

Baby Lock ellegante 2 BLG2 Specifications

General

Needle Threading	Automatic
LCD Touch Screen	Yes
Connectivity	USB
Automatic Thread Cutter	Yes
Built-in Memory	Yes
Needle Positions	15
Type	Embroidery and Sewing
Maximum Sewing Speed	1000 stitches per minute