EasyManua.ls Logo

Baby Lock Solaris 2 - User Manual

Baby Lock Solaris 2
6 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Copyright 2004-2021 Baby Lock USA
Customer Support: 1-800-313-4110
BLSA2 Ver.3.51 Software Update – p.1
Baby Lock Solaris 2
(Model BLSA2)
Software Update Version 3.51
August 2021
Introduction
If the software version of your Solaris 2 (Model BLSA2) is earlier than version 3.51, an update
program is now available for download to improve its performance.
Note:
Some memorized settings might be altered. For best results, test stitch before using saved stitches.
Version 3.51 update will provide the following changes:
1. Reduced operating noise when using the Digital Dual Feed Foot.
How to confirm the software version of your BLSA2
1. Press the power switch to "|" to turn on your machine.
2. If the opening movie is played, touch anywhere on the LCD screen.
3. Press (Machine setting screen key) to display the machine's settings screen.
4.
The machine's settings screen appears.
5.
Switch the settings screens by using (Previous page key) or (Next page key) to
display the machine's program version.

Other manuals for Baby Lock Solaris 2

Preview: Instruction And Reference Guide
Instruction And Reference Guide224 pages

Questions and Answers

  • B
    Brandy FigueroaJul 26, 2025
    Why bobbin thread does not wind neatly on my Baby Lock Solaris 2?
    • C
      Corey KelleyJul 26, 2025
      If the bobbin thread isn't winding neatly on your Baby Lock Sewing Machine, it could be due to a few reasons. Make sure the thread is passed correctly through the bobbin winding thread guide. If the bobbin spins slowly, press in the bobbin winding window to increase the winding speed. Also, ensure the thread that was pulled out is wound around the bobbin 5 or 6 times clockwise, and that the empty bobbin is set properly on the pin until you hear it click.
  • T
    Tim PerkinsJul 31, 2025
    What to do if I cannot pull up the bobbin thread on my Baby Lock Sewing Machine?
    • H
      holmesrebeccaJul 31, 2025
      If you're unable to pull up the bobbin thread on your Baby Lock Sewing Machine, the needle may be turned, bent, or dull, so replace it. Alternatively, the bobbin might be set incorrectly; in that case, reset the bobbin thread correctly.
  • K
    Krista WhiteAug 5, 2025
    What to do if the bobbin thread winds below the bobbin winder seat on my Baby Lock Solaris 2?
    • R
      Roger BondAug 5, 2025
      If the bobbin thread winds below the bobbin winder seat while winding the bobbin on your Baby Lock Sewing Machine, it's likely that you didn't wind the bobbin thread properly initially, or the thread wasn't correctly set in the guides. Remove the thread wound below the bobbin winder seat, and then wind the bobbin correctly. Follow the images on the machine for guidance when threading for bobbin winding.
  • J
    James JohnsonAug 9, 2025
    What to do if nothing appears on my Baby Lock Sewing Machine LCD?
    • M
      Michelle GonzalezAug 9, 2025
      If nothing is appearing on the LCD screen of your Baby Lock Sewing Machine, first, ensure that the main power switch is turned on. Also, verify that the power cord is properly inserted into an electrical outlet.
  • J
    jonathon25Aug 14, 2025
    What to do if the Baby Lock Solaris 2 screen has been locked?
    • T
      Travis ThompsonAug 15, 2025
      If nothing happens when you press the LCD display on your Baby Lock Sewing Machine, the screen might be locked. Press either of the unlocking keys to unlock the screen.
  • J
    jessicafoxAug 20, 2025
    Why is my Baby Lock Solaris 2 LCD screen not clear?
    • J
      Julia GomezAug 20, 2025
      If the LCD screen on your Baby Lock Sewing Machine doesn't look very clear, it might be that the screen brightness needs adjusting. Go to the settings screen and adjust the “Screen Display Brightness”.

Summary

Introduction and Version Check

How to Confirm Software Version

Detailed steps to navigate the machine interface and verify the current software version.

How to Update Your Machines Software

Update via USB Flash Drive

Instructions for preparing a USB drive and transferring the update file to the machine.

Update via Wireless Network

Steps for downloading and installing software updates directly from the machine via Wi-Fi.

Software Update History

Version 3.50 Update Details

Changes and improvements introduced in software version 3.50.

Version 3.06 Update Details

Enhancements and functionality updates for version 3.06.

Version 3.05 Update Details

Specific improvements for version 3.05, focusing on the LED pointer.

Version 3.04 Update Details

Features and enhancements included in version 3.04.

Baby Lock Solaris 2 Specifications

General IconGeneral
BrandBaby Lock
ModelSolaris 2
CategorySewing Machine
LanguageEnglish

Related product manuals