The
control panel
will be
disabled
until
power
returns.
Spa
settings
Power has been
cut
off
to the spa.
will be
preserved
until next
power
up.
After
the pump
has been
running
for
1 minute, the current water
temperature
will be displayed.
“Overheat”
- The
spa has
shut
down.*
One
of
the
DO NOT ENTER THE WATER.
Remove
the
spa cover
and allow
sensors has detected 118°F/47.8°C
at the heater.
water
to
cool. Once
the
heater has cooled, reset
by pushing any
button. If
spa does
not
reset,
shut
off
the
power
to the
spa
and call
your dealer
or
service
organization.
“Overheat”
- The
spa has
shut
down.*
One of
DO NOT ENTER THE WATER.
Remove
the
spa cover
and allow
the
sensors has detected
that the
spa water
is
water
to
cool.
At
107°F/41.7°C,
the
spa should automatically
reset.
If
spa does
not
reset,
shut
off
the
power
to the
spa
and
call
your
dealer
or
service
organization.
Spa
is shut
down.*
The
sensor
that is plugged into
If the
problem persists, contact your dealer
or
service
organization.
the
Sensor “A” jack
is not working.
(May appear temporarily
in an
overheat
condition.)
Spa
is shut
down.*
The
sensor
that is plugged into
If the
problem persists, contact your dealer
or
service
organization.
the
Sensor “B” jack
is not working.
(May appear temporarily
in an
overheat
condition.)
Sensors are
out
of balance.
If alternating with spa
If the
problem persists, contact your dealer
or
service
organization.
temperature,
it
may
just be a
temporary
condition.
If
flashing
by
itself, spa
is shut down.*
A
significant difference between
temperature
If the
water level
is
normal, make sure
all pumps
have been
primed.
sensors has been detected.
This
could indicate
a
If
problem persists, contact your dealer
or
service
organization.
Persistent low flow problems. (Displays
on the
Follow action required
for
message.
Heating
capability of
the
fifth occurrence
of
message
within 24 hours.)
spa
will not
reset automatically; you may press any
button to reset.
Heater is shut
down,
but other
spa
functions
continue
to run normally.
Possible inadequate water, poor flow,
or air
If
water level
is
normal, make sure
all pumps
have
been
bubbles
in
detected
in the
heater. Spa
is shut down
primed.
Press any
button to
reset.
This
message
will reset
within 15 minutes. If
problem persists, contact your dealer
or
Inadequate water detected
in
heater. (Displays
on
Follow action required
for
message. Spa
will not automatically
third
occurrence
of
message.) Spa
is
shut down.*
“Ice”
- Potential
freeze condition
detected.
*
-
E
v
e
n
w
hen
s
p
a
is
s
h
u
t
d
o
w
n
,
so
m
e
e
q
u
ip
m
e
n
t
w
i
ll
turn on
if
freeze
protection
is
needed
.
reset. Press any
button to
reset
manually.
No
action required.
All equipment will
automatically
activate
regardless of spa
status. The equipment
stays
on 4 minutes
after
the
sensors
detect that the
spa temperature has risen
to
45°F/7.2°C
or
higher. An
optional freeze sensor may
be
added
to protect against
extraordinary freeze conditions. Auxiliary freeze sensor protection
is
advisable
is
colder climates. See your dealer for
details.
Warning! Shock Hazard! No User Serviceable
Parts.
Do not attempt
service of
this
control system. Contact your dealer
or
service organization for assistance. Follow
all
owner’s manual power
connection instructions. Installation
must be
performed
by a licensed
electrician
and all grounding
connections
must be
properly
installed.
To Previous Page
Loading...
