To Next PageTo Next Page
Need help?Do you have a question about the Barreto 30SG and is the answer not in the manual?
Explains the international safety alert symbol, signal words (Danger, Warning, Caution), and their usage.
Covers risks like cutter wheel contact, flying debris, loud noise, and exhaust fumes.
Addresses risks associated with inclines, parking on slopes, and machine movement.
Warns against operating near flammable materials, sparks, and hot engine components.
Details necessary PPE like face shields, hard hats, hearing protection, boots, and gloves.
Provides critical safety guidelines for handling batteries and using the electric starter, including acid and fume hazards.
Emphasizes the importance of studying all safety and operating instructions before use.
States the requirement to check engine oil, fuel, and hydraulic fluid levels before starting.
Stresses the need to understand all controls before commencing operation.
Explains the functions of the ignition switch for starting/stopping and the throttle for engine speed.
Details operation of track controls for movement/steering and cutter head control for positioning.
Describes the location and function of the parking brake for securing the machine.
Specifies the function of the fuel valve and the use of the choke for cold starts.
Identifies the ignition switch and throttle lever for engine operation.
Covers checking fluid levels, fuel level, and opening the fuel shutoff valve.
Instructions on using the choke for cold starts and setting the throttle.
Guidance on operating the starter motor, including time limits and potential overheating.
Provides guidance for operating the machine in cold weather conditions, including fluid changes and warm-up procedures.
Details checks for oil, fuel, cooling areas, and engine components before starting.
Instructions for setting the throttle and using the key switch to start the engine.
Information on priming dry fuel systems, starter limits, and potential noises.
Covers oil level, disengaging drive controls, and fuel valve operation.
Details setting the throttle, choke, and activating the stop switch.
Instructions on using the electric start switch to ignite the engine.
Guidance for priming a dry fuel system and handling engine start issues.
Lists requirements for operator age, capability, and manual study.
Details essential PPE like face shields, hard hats, hearing protection, boots, and gloves.
Presents technical data regarding the noise emission levels of the stump grinder.
Displays measured sound power and pressure levels according to ISO 4871 standards.
States the average measured vibration emission value and its uncertainty.
Explains how safety gloves can mitigate vibration effects and prevent injury.
Assesses the risk of hand-arm vibration syndrome based on emission levels.
Cites OSHA requirements and the procedure for calling utility locating services.
Explains color codes for utilities and warns about dangers from electric, gas, and fiber optic lines.
Advises a thorough inspection of the work site for safety hazards and obstructions.
Covers outdoor operation, lighting, clearances, and keeping others away.
Warns about operating near flammable materials and potential ignition sources.
Instructions on immediate actions upon striking wires, cables, or pipes.
Details specific dangers associated with electric, gas, and fiber optic lines.
Steps for positioning the machine and starting the cutter wheel.
Describes how to swing the cutter, adjust depth, and move the machine for effective grinding.
Offers advice like clearing the area, maintaining throttle, and cutting edges for efficiency.
Provides the correct steps for safely stopping the stump grinder's engine and securing it.
Recommends PPE for battery handling and warns about acid and fumes.
Details the sequence for connecting jumper cables safely and starting the engine.
Instructions for safely removing cables and the requirement for a 12-volt system.
Covers raising the cutter, warnings about the cutter wheel, and keeping clear of tracks.
Advises on smooth operation, caution on uneven ground, and avoiding inclines.
Specifies the maximum allowable incline angle for safe operation.
Steps for enabling towing by loosening bypass plugs and disengaging the brake.
Specifies towing distance/speed limits and closing bypass valves.
Instructions for manually raising the cutter head when power is unavailable, with weight warnings.
Checklist for towing vehicle, hitch, and safety chains before road transport.
Step-by-step guide for loading the stump grinder onto a tilt bed trailer.
Step-by-step guide for safely unloading the stump grinder from a tilt bed trailer.
Steps for loading the stump grinder onto a truck bed using ramps.
Steps for safely unloading the stump grinder from a truck bed using ramps.
Steps for loading the stump grinder onto a truck bed using a hoist, including equipment and safety checks.
General