Barudan BEVT-Z1501C - User Manual

Questions and Answers

H
Hannah GordonAug 17, 2025
What to do if my Barudan BEVT-Z1501C machine won't power up?
- J
  Joshua WatsonAug 17, 2025
  If your Barudan Lubrication systems machine won't power up, it might be due to the EMERGENCY STOP switch being engaged or a blown fuse. First, turn the EMERGENCY STOP switch clockwise to release it. Then, try powering the machine on again. Also, check the fuse.
M
Mrs. Kayla Moore PhDAug 19, 2025
Why does my Barudan BEVT-Z1501C machine stop, even though the thread isn't broken?
- E
  ericmorganAug 20, 2025
  Your Barudan Lubrication systems machine might be stopping without a thread break for several reasons. It could be that the sewing head is turned off while the thread break indicator switch is on; if so, turn the thread break indicator switch off when heads are not in use. Alternatively, the thread might not be properly threaded, so ensure the thread path is completely threaded. Other potential causes include a faulty take-up spring (make sure it's bouncing freely, and replace it if needed).
S
Samuel SchwartzAug 22, 2025
Why is the thread breaking on my Barudan BEVT-Z1501C machine?
- H
  hryanAug 23, 2025
  Thread breaks on your Barudan Lubrication systems machine can occur for several reasons. Check if the flow of the top thread is obstructed; if the top tension is too tight, ensure the thread isn't caught on the tension disks, thread rack, or thread spindle, and that it's not looped around the take-up spring. The machine might also be running too fast for the application, so try reducing the speed. Other causes include a burr on the bobbin case (buff with emery and crocus cloth or replace the bobbin case), a burr or excessive wear on the hook (replace the entire hook assembly), or scratches, needle marks, or burrs on the throat plate (polish flat surfaces and the hole). Finally, check for a burr on the front edge of the hook and polish it.
B
Brandon WilliamsAug 25, 2025
How to fix fabric puckering on my Barudan Lubrication systems machine?
- D
  danapetersonAug 26, 2025
  Fabric puckering on your Barudan Lubrication systems machine can be fixed by: * Rehooping the garment, ensuring it is taut. * Using appropriate backing to stabilize the fabric. * Hooping the backing along with the garment; for more stability, bond the backing or topping to the garment. * Adjusting the tensions so that only one third bobbin thread shows on the underside of the embroidery.
M
Mark BrooksAug 28, 2025
What causes needle breaks on a Barudan BEVT-Z1501C Lubrication systems machine and how to prevent them?
- R
  Randall MooreAug 28, 2025
  Needle breaks on a Barudan Lubrication systems machine can be caused by several factors. Ensure the needle is fully inserted into the needle bar shaft with the long groove in front, and that the needle clamp screw is tight. Check for obstructions in the thread flow, making sure the thread isn't caught anywhere and the top tension isn't excessively tight. Other causes include the needle being too close to the hook (hook needs re-timing), the needle hitting the hoop (use a larger hoop), or a bent needle (replace it).
K
Katelyn MillerAug 31, 2025
Why are stitches not being formed on my Barudan BEVT-Z1501C Lubrication systems machine?
- B
  bpowellAug 31, 2025
  Stitches may not form on your Barudan Lubrication systems machine if the bobbin is empty (replace with a full bobbin), or if there isn't enough bobbin thread pulled out of the bobbin case (ensure at least three inches are hanging out). Also, check that the needle is correctly inserted all the way into the needle bar shaft with the long groove in front and that the needle clamp screw is tight. Other potential causes include timing issues (re-time the hook), a broken hook point (replace the hook assembly), or the thread not being threaded through the take-up lever (check all threading points).
R
rebecca59Sep 2, 2025
What causes thread "birdnests" under the throat plate area on a Barudan Lubrication systems machine?
- A
  Allison SpencerSep 3, 2025
  Thread “birdnests” under the throat plate area on a Barudan Lubrication systems machine can be caused by several issues. These include improper threading (check all threading points), loose hooping (ensure fabric is hooped securely with proper backing), lack of lubrication in the hook assembly (place one drop of oil in the oiling point), using a fill stitch on very small areas (change to a satin stitch), tension problems (adjust the tension and check the bobbin case tension), a faulty take-up spring (replace it), a dull needle (replace it), or a needle that is too large (change to a smaller needle).
M
michael56Sep 5, 2025
What causes a frayed thread break on my Barudan Lubrication systems machine?
- D
  diazvickieSep 5, 2025
  A frayed thread break on your Barudan Lubrication systems machine can be due to a burr on the eye of the needle (replace the needle), a worn needle eye (especially with metallic thread, so replace the needle and try an over-sized needle), or worn or burred ceramic eyelets or ivory thread guides (polish lightly or replace; use clear nail polish as a temporary fix). Also, the eye of the needle might be too small (change to a larger needle; use an 11/75 or 10/70 needle for 40 weight rayon thread).
E
Eric SmithSep 8, 2025
Why are thread breaks undetected on my Barudan BEVT-Z1501C machine?
- T
  Tamara AdkinsSep 8, 2025
  Undetected thread breaks on your Barudan Lubrication systems machine may be due to dirty sensors. Also, verify that the machine is not set for a boring device in MC Parameter 1; ensure the Borer parameter is set to Ø.
K
Kim GonzalezSep 12, 2025
What causes thread frays and breaks on a Barudan BEVT-Z1501C Lubrication systems machine?
- D
  David EdwardsSep 12, 2025
  Thread fraying and breaking on your Barudan Lubrication systems machine can be caused by weak spots or knots in the thread. If this shows up as an infrequent break, replace the thread.