What to do if my Barudan Lubrication systems machine won't power up?
If your Barudan Lubrication systems machine won't power up, it might be due to the EMERGENCY STOP switch being engaged or a blown fuse. First, turn the EMERGENCY STOP switch clockwise to release it. Then, try powering the machine on again. Also, check the fuse.
Why does my Barudan BEVT-Z1501CB machine stop, even though the thread isn't broken?
Your Barudan Lubrication systems machine might be stopping without a thread break for several reasons. It could be that the sewing head is turned off while the thread break indicator switch is on; if so, turn the thread break indicator switch off when heads are not in use. Alternatively, the thread might not be properly threaded, so ensure the thread path is completely threaded. Other potential causes include a faulty take-up spring (make sure it's bouncing freely, and replace it if needed).
Why is the thread breaking on my Barudan BEVT-Z1501CB machine?
Thread breaks on your Barudan Lubrication systems machine can occur for several reasons. Check if the flow of the top thread is obstructed; if the top tension is too tight, ensure the thread isn't caught on the tension disks, thread rack, or thread spindle, and that it's not looped around the take-up spring. The machine might also be running too fast for the application, so try reducing the speed. Other causes include a burr on the bobbin case (buff with emery and crocus cloth or replace the bobbin case), a burr or excessive wear on the hook (replace the entire hook assembly), or scratches, needle marks, or burrs on the throat plate (polish flat surfaces and the hole). Finally, check for a burr on the front edge of the hook and polish it.
How to fix fabric puckering on my Barudan BEVT-Z1501CB Lubrication systems machine?
Fabric puckering on your Barudan Lubrication systems machine can be fixed by: * Rehooping the garment, ensuring it is taut. * Using appropriate backing to stabilize the fabric. * Hooping the backing along with the garment; for more stability, bond the backing or topping to the garment. * Adjusting the tensions so that only one third bobbin thread shows on the underside of the embroidery.
What causes needle breaks on a Barudan BEVT-Z1501CB Lubrication systems machine and how to prevent them?
Needle breaks on a Barudan Lubrication systems machine can be caused by several factors. Ensure the needle is fully inserted into the needle bar shaft with the long groove in front, and that the needle clamp screw is tight. Check for obstructions in the thread flow, making sure the thread isn't caught anywhere and the top tension isn't excessively tight. Other causes include the needle being too close to the hook (hook needs re-timing), the needle hitting the hoop (use a larger hoop), or a bent needle (replace it).
Why are stitches not being formed on my Barudan BEVT-Z1501CB Lubrication systems machine?
Stitches may not form on your Barudan Lubrication systems machine if the bobbin is empty (replace with a full bobbin), or if there isn't enough bobbin thread pulled out of the bobbin case (ensure at least three inches are hanging out). Also, check that the needle is correctly inserted all the way into the needle bar shaft with the long groove in front and that the needle clamp screw is tight. Other potential causes include timing issues (re-time the hook), a broken hook point (replace the hook assembly), or the thread not being threaded through the take-up lever (check all threading points).
What causes thread "birdnests" under the throat plate area on a Barudan Lubrication systems machine?
Thread “birdnests” under the throat plate area on a Barudan Lubrication systems machine can be caused by several issues. These include improper threading (check all threading points), loose hooping (ensure fabric is hooped securely with proper backing), lack of lubrication in the hook assembly (place one drop of oil in the oiling point), using a fill stitch on very small areas (change to a satin stitch), tension problems (adjust the tension and check the bobbin case tension), a faulty take-up spring (replace it), a dull needle (replace it), or a needle that is too large (change to a smaller needle).
What causes a frayed thread break on my Barudan Lubrication systems machine?
A frayed thread break on your Barudan Lubrication systems machine can be due to a burr on the eye of the needle (replace the needle), a worn needle eye (especially with metallic thread, so replace the needle and try an over-sized needle), or worn or burred ceramic eyelets or ivory thread guides (polish lightly or replace; use clear nail polish as a temporary fix). Also, the eye of the needle might be too small (change to a larger needle; use an 11/75 or 10/70 needle for 40 weight rayon thread).
Why are thread breaks undetected on my Barudan BEVT-Z1501CB Lubrication systems machine?
Undetected thread breaks on your Barudan Lubrication systems machine may be due to dirty sensors. Also, verify that the machine is not set for a boring device in MC Parameter 1; ensure the Borer parameter is set to Ø.
What causes thread frays and breaks on a Barudan Lubrication systems machine?
Thread fraying and breaking on your Barudan Lubrication systems machine can be caused by weak spots or knots in the thread. If this shows up as an infrequent break, replace the thread.
General precautions for machine operation, electrical safety, and handling hazards.
Guidelines for proper machine grounding and explanation of warning labels.
Procedures for powering on, origin setting, modes, and screen navigation.
Overview of USB memory capabilities, functions, and folder organization.
Methods for saving, loading, and transferring multiple designs using USB.
Modifying pattern parameters and defining embroidery areas.
Setting start points, entering drive mode, and adjusting sewing speed.
Procedures for modifying and resetting machine condition parameters.
Information on configuring and operating the network system.
Comprehensive list of error messages, their causes, and solutions.
Steps for installing the machine, including tools, site prep, and electrical needs.
Guidance on resolving common problems and performing key mechanical adjustments.
General| Brand | Barudan |
|---|---|
| Model | BEVT-Z1501CB |
| Category | Lubrication systems |
| Language | English |
To Next Page
