Baruffaldi CE Series - 5.3 Flow Chart & ISO Program Example

59 pages

Save Page as PDF

To Next Page

To Previous Page

USE AND MAINTENANCE MANUAL

2-Speed Gearboxes Series CE

M.CE.GEN.ENG.DOCX

Issued

2018

Rev.03

Page 56 / 59

5.3 FLOW CHART & ISO PROGRAM EXAMPLE

Main Page

Table of Contents4
Structure of the Gearbox6
Delivery Conditions7
Data Label8
Handling and Lifting the Gearboxes9
Technical Data10
Ordering Code12
Motor Flange Dimensions13
Functioning Principle14
Main Description14
Gearbox in High Speed Mode (1:1)15
Gearbox in Low Speed Mode (1:I)15
Gearbox in Neutral Mode15
General Operating Rules16
Gearbox Start-Up17
Motor Specifications17
Dimensions and Tolerances17
Motor Balancing17
Matching Motor - Gearbox Balancing18
Screws Tightening Torque18
Assembling the Motor on the Gearbox - Gearbox CE 11 - 13 - 13+ - 16 - 18 - 2019
Motor Shaft with Key19
Motor Shaft Without Key (Straight Shaft) - Conical Clamping Unit20
Disassembling the Clamping Unit (100) from Motor Shaft23
Assembling the Motor on the Gearbox - Gearbox Type CE 12 - 14 - 1524
Motor Shaft with Key24
Motor Shaft Without Key (Straight Shaft) - Conical Clamping Unit26
Assembling the Gearbox on the Motor27
Motor-Gearbox Assembling Options28
Gearbox Output29
Verifying Gearbox Output Loading Capacity29
Gearbox Output Bearings: Position and Loading Capacity30
Assembling Positions and Lubrication31
Choosing the Lubrication Mode31
Splash Lubrication32
Monitoring the Oil Level: Oil Sight-Glass and Oil Level Sensor32
Oil Recirculating Lubrication (Forced Lubrication)34
Monitoring the Oil Flow: Oil Flow Rate Switch35
Dimensioning Oil Cooling Systems - Cooling Power35
Gearbox Assembling Designation36
Lubrication Examples36
CE 13 - Horizontal Assembly - Forced Lubrication with Suction Pump37
CE 13 - Horizontal Assembly - Forced Lubrication with Oil Return by Fall down37
CE 13 - Vertical down Assy - Forced Lubrication with Oil Return by Suction38
CE 13 - Horizontal Assy - Forced Lubrication with Oil Return by Fall down38
CE 20 - Horizontal Assembly - Forced Lubrication with Suction Pump39
CE 20 - Horizontal Assembly - Forced Lubrication with Oil Return by Fall down39
CE 20 - Horizontal Assembly - Forced Lubrication with Oil Return by Fall down40
CE 20 - Horizontal Assembly - Forced Lubrication with Suction Pump40
CE 20 - Vertical down Assembly - Forced Lubrication with Suction Pump41
CE 20 Vertical down Assy - Forced Lubrication with Oil Return by Fall down41
Assembling Positions & Lubrication - CE 1142
Assembling Positions & Lubrication - CE 16 & 1842
Assembling Positions & Lubrication - CE 1244
Assembling Positions & Lubrication - CE 13 & CE1346
Assembling Positions & Lubrication - CE 14 & CE 1548
Assembling Positions & Lubrication - CE 2052
Assembling Positions & Lubrication - CEA13 & CEA 1354
Assembling Positions & Lubrication - CEA14 & CEA 1554
Electrical Section55
Actuator55
Circuit Diagram55
Flow Chart & Iso Program Example56
Gearbox Layout Views58
Gearbox Type CE 11 - 13 - 13+ - 16 - 18 - 2058
Gearbox Type CE 12 - 14 -1559

Baruffaldi CE Series - 5.3 Flow Chart & ISO Program Example

Table of Contents

Related product manuals