Page 10 <&(%$*4.8"4,7%K'*#$"&8#L%/7*,#*%4,77%HMNNNMNIIMOPQP1 Item 63444
?@<6AR ST6;@ACSE D@CEA6E@EU6?6AFT
S/*(,$"83%C8#$('4$"&8#
% ;*,9%$.*%6EAC;6%CDTS;A@EA%?@<6AR%CE<S;D@ACSE%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
A&&7%?*$%F/
AS%T;6!6EA%?6;CSF?%CEiF;R%<;SD%@UUCY6EA@G%ST6;@ACSE-%
D,J*%#'(*%$.,$%$.*%A("33*(%"#%"8%$.*%&22M/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%"$#%
*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8>%/(&4*9'(*%"8%$."#%#*4$"&81
AS%T;6!6EA%?6;CSF?%CEiF;R-%
V*,(%@E?CM,//(&Z*9%#,2*$>%3&337*#L%.*,Z>M9'$>%)&(J%37&Z*#L%,89%.*,Z>M9'$>%
7&83M#7**Z*9%#."($%&(%4&,$%).*8*Z*(%.,897"83%&(%)&(J"83%8*,(%$.*%X7,9*1%%%
A.*%X7,9*%4,8%#'99*87>%#/("83%&'$%9'("83%#*(Z"4*1
X7,9*%?*7*4$"&8
V@;ECEWj%%AS%T;6!6EA%?6;CSF?%CEiF;R%<;SD%XG@Y6%USDCEW%GSS?6L%%
SEGR%F?6%XG@Y6?%S<%AB6%?T6UC<C6Y%?Ck61
Select the proper Blade according to the cutting
material and the diameter of the workpiece.
This Band Saw comes with a 14 teeth-per-inch Blade.
It accepts Ǝ[Ǝ[Ǝ Blades.
14 TPI - Soft/ Thick Material
(aluminum, lead, rubber-like material, wood)
24 TPI - Hard/Thin Material
(cast iron, soft steel, hard steel)
X7,9*%C8#$,77,$"&8%,89%;*/7,4*5*8$
AS%T;6!6EA%?6;CSF?%CEiF;R%<;SD%@UUCY6EA@G%ST6;@ACSE-%
D,J*%#'(*%$.,$%$.*%A("33*(%"#%"8%$.*%&22M/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%
"$#%*7*4$("4,7%&'$7*$%+*2&(*%"8#$,77"83%&(%(*5&Z"83%,%#,)%X7,9*1
1. Set the Frame so that the edge of the used
Blade is pointing away from you. (Once Blade
tension is released, it may spring off quickly.)
2. Turn the Tension Handle away from the body
of the Bandsaw to release Blade tension. Slide
old Blade off Gear Wheels. See Figure B.
W*,(%V.**7#
X7,9*
<"3'(*%X-%%X7,9*%C8#$,77,$"&8
E&$*- Install Blade with teeth
pointing upward, facing you.
3. Set the Blade into both Guide Bearings
and center it on them, see Figure C.
W'"9*%X*,("83
<"3'(*%U-%%W'"9*%X*,("83
4. Tension Blade according to instructions
in Blade Tensioning section.
To Next Page
Loading...
